Close

Search:

Type: Posts; User: Rob@RBTurbo

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds; generated 2 minute(s) ago.

  1. We still sell a good amount of N54 turbo setups,...

    We still sell a good amount of N54 turbo setups, in fact we are at 4 sets so far this week, so we are definitely not going to turn it away. But well agree that there are better markets to spend the...
  2. Between the M2/M3/M4 there should be a lot of...

    Between the M2/M3/M4 there should be a lot of happiness, just need to get some of these out there and get some data/feedback now. The only set we have shipped is part of an engine build project,...
  3. The turbos were delivered on Monday to Ghassan...

    The turbos were delivered on Monday to Ghassan and now the ball is in their court with the final assembly, we can't wait to see more info/data on the finished products!

    Rob
  4. Yeah, we've yet to check out all the PN's for...

    Yeah, we've yet to check out all the PN's for 100% confirmation but we fully suspect they will be identically casted for all 2014+ M3/M4 and 2018+ M2 (equipped with the S55 engine).
  5. Replies
    43
    Views
    3,549

    General: The aftermarket ball bearing technology, as we'd...

    The aftermarket ball bearing technology, as we'd mentioned above, has a very sketchy reputation. While not cheap to produce, purchase, utilize, etc.; they are no good to invest in to ultimately fail....
  6. N54: The RB GF's are purely art, without a doubt the...

    The RB GF's are purely art, without a doubt the tallest bar was set with these units, and if they were to have any issues there simply is just not going to be anything better that can be offered for...
  7. Yes sir can't really beat this price whatsoever...

    Yes sir can't really beat this price whatsoever based on what we are seeing out there right now, appreciate the front page!



    Love this project so much it makes me want to pick one up too...
    ...
  8. More CNC Inlet Port Matching pics.

    More CNC Inlet Port Matching pics.
  9. RB Turbo S55 RB Twos Turbo Upgrade/Inlet Package MSRP $2,899

    All,

    Been a long time coming but going into 2020 we made an internal deal to start opening up to some of these other markets that we have so long ignored, yet find much more lucrative, than the...
  10. S55 RB Twos project completed and shipping today....

    S55 RB Twos project completed and shipping today. Spent a lot of time diligently customizing, machining, and building these units; we expect one hell of a solid all around setup. Here are some more...
  11. While we are new to the S55 market, we've seen a...

    While we are new to the S55 market, we've seen a fair share of issues with the "boxed ready to go on the shelf" China turbos for the N54 market. A well built custom turbo by the right facility using...
  12. N54: Says the guy who came in here crapping on us...

    Says the guy who came in here crapping on us while not even listening to his own supplier, amidst currently supporting/advertising/sponsoring the largest N54 turbo product debacle the world has ever...
  13. N54: Hey look the goofus, "I ate too many paint chips...

    Hey look the goofus, "I ate too many paint chips as a kid", vendor of the decade strikes again. Yes sir, the memory is so short there, soooo very short that we actually made mention of it 10 DAYS AGO...
  14. N54: Marty in the next couple years, one of easily 50+...

    Marty in the next couple years, one of easily 50+ with this same (or similar) story:
    https://www.n54tech.com/forums/showthread.php?t=60614
  15. N54: Amen sir, 11.1 sec 1/4 mile right? Some of the...

    Amen sir, 11.1 sec 1/4 mile right? Some of the best ET's we'd seen from you over the years on those old Classic RB's with an OE engine and only the BASIC OTS supporting mods, you brought it back then...
  16. Replies
    113
    Views
    19,022

    N54: As a competitive vendor voice here, I also do not...

    As a competitive vendor voice here, I also do not see the harm in cranking the bolt just a bit more using the proper tools, if anything with time elapsed since initial install it actually could be...
  17. N54: This company just gets weirder and weirder, now...

    This company just gets weirder and weirder, now they have taken down their Facebook page. We are sure it was simply a fraudulent page, started by some other shadow.

    Rob
  18. Replies
    43
    Views
    3,549

    General: Ah, cool. Must simply be a fluke of ghosting the...

    Ah, cool. Must simply be a fluke of ghosting the poor french guy after spending ~$5k on Ball Bearing MMP 1k's 4 months ago.
  19. Replies
    43
    Views
    3,549

    General: Agreed, it must only take the Vendors request to...

    Agreed, it must only take the Vendors request to have ECS offer your products? Don't know, personally have never looked into it, but would find it every odd if they request it of vendors and they...
  20. Replies
    43
    Views
    3,549

    General: Anything more on this one? See this post made the...

    Anything more on this one? See this post made the other day on another forum (Translated using google):
    "hello can someone tell me if mmp is having trouble right now because i ordered turbo 1k ball...
  21. N54: What is the new date set for this giveaway?!:cool:

    What is the new date set for this giveaway?!:cool:
  22. N54: Good news sir! Sounds like these units had to...

    Good news sir! Sounds like these units had to make quite the journey to get to you, even after some delays on our end to get them over! Hopefully you are impressed with them in hand, and we...
  23. Some teaser shots of the upcoming S55 RB Twos....

    Some teaser shots of the upcoming S55 RB Twos. Keep in mind these are not designed to be the end all be all setup, and we know 100% are not going to take down the competitions peak numbers, and this...
  24. N54: Looks like another quarter has passed, time flies...

    Looks like another quarter has passed, time flies when your having fun!:dance: All has been going great here, still kicking out plenty of N54 turbos, but not going to lie it has been slowing down...
  25. Yes sir that is indeed his set. We were able to...

    Yes sir that is indeed his set. We were able to CNC both the OE rear elbow and the OE front plastic inlet perfectly to match, which is what those pictures were trying to convey. So this offering will...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4