Close

Page 7 of 19 FirstFirst ... 5678917 ... LastLast
Results 151 to 175 of 452
  1. #151
    Join Date
    Dec 2010
    Posts
    221
    Rep Points
    344.4
    Mentioned
    6 Post(s)
    Rep Power
    4



    Yes Reputation No

    Custom made Setrab oil cooler in position

    We have found the right place and position for our Setrab oil cooler. Before the oil cooler, there is a modified (still needs some plastic works) M3 air duct to flow the air to the oil cooler.
    Attached Images Attached Images     

  2. #152
    Join Date
    Dec 2010
    Posts
    221
    Rep Points
    344.4
    Mentioned
    6 Post(s)
    Rep Power
    4



    1 out of 1 members liked this post. Yes Reputation No

    Concept of a Custom made hand-brake master cylinder

    As we have replaced the factory brake hat and rotor on our car, we have realized that the factory hand-brake system on the rear is not operating as effecient as used to be (our custom made brake hat is a little bit larger than the old one).

    We decided to make a hybrid hand-brake system, which uses the same hand-brake knob, hand-brake bowden. At the rear, a special master cylinder is connected, which is applied by the factory brake bowden. The hand-brake master cylinder is connected to the rear brake calipers and operates them.
    Attached Images Attached Images       

  3. #153
    Join Date
    Jun 2013
    Location
    North Houston
    Posts
    1,295
    Rep Points
    1,639.5
    Mentioned
    111 Post(s)
    Rep Power
    17


    Yes Reputation No
    http://www.wilwood.com/Calipers/Cali...me=Mech%20Spot




    why not just use this with the mechanical brake cable one one caliper? Its how all the super car's do it (Lamborghini, ferrari, porsche, etc.etc.)
    Click here to enlarge
    Burger Motorsports dealer
    Turner Motorsports dealer
    Bimmerworld dealer
    Active Autowerks Dealer
    Shipping built/stroked/CNC ported N54's Internationally!
    Follow us!
    http://www.facebook.com/BMWdoctor
    http://twitter.com/abrhouston
    http://instagram.com/abrhouston/
    http://abrhouston.com
    http://abr.genbook.com Book online appointments!

  4. #154
    Join Date
    Dec 2010
    Posts
    221
    Rep Points
    344.4
    Mentioned
    6 Post(s)
    Rep Power
    4



    Yes Reputation No
    Click here to enlarge Originally Posted by alex@ABRhouston Click here to enlarge
    http://www.wilwood.com/Calipers/Cali...me=Mech%20Spot


    why not just use this with the mechanical brake cable one one caliper? Its how all the super car's do it (Lamborghini, ferrari, porsche, etc.etc.)
    Good idea anyway. Thanks for your feedback.

  5. #155
    Join Date
    Jul 2010
    Location
    Encino,CA
    Posts
    8,039
    Rep Points
    5,733.6
    Mentioned
    179 Post(s)
    Rep Power
    58


    Yes Reputation No
    What size oil cooler is that? 32 row?
    Burger Motorsports
    Home of the Worlds fastest N20s, N54s, N55s, S55s, N63s, and S63s!

    It is the sole responsibility of the purchaser and installer of any BMS part to employ the correct installation techniques required to ensure the proper operation of BMS parts, and BMS disclaims any and all liability for any part failure due to improper installation or use. It is the sole responsibility of the customer to verify that the use of their vehicle and items purchased comply with federal, state and local regulations. BMS claims no legal federal, state or local certification concerning pollution controlled motor vehicles or mandated emissions requirements. BMS products labeled for use only in competition racing vehicles may only be used on competition racing vehicles operated exclusively on a closed course in conjunction with a sanctioned racing event, in accordance with all federal and state laws, and may never be operated on public roads/highways. Please click here for more information on legal requirements related to use of BMS parts.

  6. #156
    Join Date
    Nov 2010
    Posts
    404
    Rep Points
    758.8
    Mentioned
    11 Post(s)
    Rep Power
    8


    Yes Reputation No
    Click here to enlarge Originally Posted by fastgti69 Click here to enlarge
    What size oil cooler is that? 32 row?
    Looks like it (and that's what I'm running). I'd suggest adding some rubber to the mounts.

    Neil

  7. #157
    Join Date
    Dec 2010
    Posts
    221
    Rep Points
    344.4
    Mentioned
    6 Post(s)
    Rep Power
    4



    Yes Reputation No
    Click here to enlarge Originally Posted by MDORPHN Click here to enlarge
    Looks like it (and that's what I'm running). I'd suggest adding some rubber to the mounts.

    Neil
    25 Row. As per he rubber, thanks, its sound good.

  8. #158
    Join Date
    Jun 2012
    Posts
    1,177
    Rep Points
    801.6
    Mentioned
    14 Post(s)
    Rep Power
    9


    Yes Reputation No
    Click here to enlarge Originally Posted by alex@ABRhouston Click here to enlarge
    http://www.wilwood.com/Calipers/Cali...me=Mech%20Spot




    why not just use this with the mechanical brake cable one one caliper? Its how all the super car's do it (Lamborghini, ferrari, porsche, etc.etc.)
    It depends what you are trying to do. If you are trying to actually use the hand brake dynamically while driving to say initiate a drift, you want a hydraulic hand brake. You do NOT want to use this for parking as the system is hydraulic and will lose pressure over time and your car will roll away. If you are trying to make a parking brake using Wilwood stuff, you could use the spot, but it really isn't that good for that purpose. For a light race car, maybe, but for a modern BMW I would say you want to use the MC4 mechanical hand brake caliper:

    http://wilwood.com/Calipers/CaliperL...4%20Mechanical

    The brake cable you want for it is made by Lokar with P/N EC-80WU. This cable is designed for the Wilwood MC4 and is not listed on Lokar's website.

    I have designed this setup for use on my Datsun with Wilwood brakes and it is the right part for the job. I do warn you though it isn't that light, but on a BMW road car that's irrelevant.
    Attached Images Attached Images   

  9. #159
    Join Date
    Jun 2013
    Location
    North Houston
    Posts
    1,295
    Rep Points
    1,639.5
    Mentioned
    111 Post(s)
    Rep Power
    17


    Yes Reputation No
    I didnt look around much after I found the mechanical calipers- but yea, the one you posted is right up a road car's alley.
    Click here to enlarge
    Burger Motorsports dealer
    Turner Motorsports dealer
    Bimmerworld dealer
    Active Autowerks Dealer
    Shipping built/stroked/CNC ported N54's Internationally!
    Follow us!
    http://www.facebook.com/BMWdoctor
    http://twitter.com/abrhouston
    http://instagram.com/abrhouston/
    http://abrhouston.com
    http://abr.genbook.com Book online appointments!

  10. #160
    Join Date
    Jun 2012
    Posts
    1,177
    Rep Points
    801.6
    Mentioned
    14 Post(s)
    Rep Power
    9


    Yes Reputation No
    Click here to enlarge Originally Posted by alex@ABRhouston Click here to enlarge
    I didnt look around much after I found the mechanical calipers- but yea, the one you posted is right up a road car's alley.
    Yeah, my first design used one of those calipers mounted to the nose of the differential with an aluminum disk on the prop shaft. Living around San Francisco though, I knew it couldn't be trusted in the hills so I abandoned it. Those calipers are surprisingly strong, but they do put a lot of loading on the cable and are probably better for large go cart sized cars.

  11. #161
    Join Date
    Jun 2013
    Location
    North Houston
    Posts
    1,295
    Rep Points
    1,639.5
    Mentioned
    111 Post(s)
    Rep Power
    17


    Yes Reputation No
    Click here to enlarge Originally Posted by rudypoochris Click here to enlarge
    Yeah, my first design used one of those calipers mounted to the nose of the differential with an aluminum disk on the prop shaft. Living around San Francisco though, I knew it couldn't be trusted in the hills so I abandoned it. Those calipers are surprisingly strong, but they do put a lot of loading on the cable and are probably better for large go cart sized cars.

    If you wanted to go driveline brake route- H.A.D. has this down pat.

    I've run their driveline brake products on many 4x4's.
    It will hold a fullsize 4x4 on 40" tires with ease- especially when its in low range, and you have spools/lockers in the differentials.
    http://highangledriveline.com/e_brake.html
    Click here to enlarge
    Burger Motorsports dealer
    Turner Motorsports dealer
    Bimmerworld dealer
    Active Autowerks Dealer
    Shipping built/stroked/CNC ported N54's Internationally!
    Follow us!
    http://www.facebook.com/BMWdoctor
    http://twitter.com/abrhouston
    http://instagram.com/abrhouston/
    http://abrhouston.com
    http://abr.genbook.com Book online appointments!

  12. #162
    Join Date
    Jul 2010
    Location
    Encino,CA
    Posts
    8,039
    Rep Points
    5,733.6
    Mentioned
    179 Post(s)
    Rep Power
    58


    Yes Reputation No
    Click here to enlarge Originally Posted by MDORPHN Click here to enlarge
    Looks like it (and that's what I'm running). I'd suggest adding some rubber to the mounts.

    Neil
    Did you make your own kit?
    Burger Motorsports
    Home of the Worlds fastest N20s, N54s, N55s, S55s, N63s, and S63s!

    It is the sole responsibility of the purchaser and installer of any BMS part to employ the correct installation techniques required to ensure the proper operation of BMS parts, and BMS disclaims any and all liability for any part failure due to improper installation or use. It is the sole responsibility of the customer to verify that the use of their vehicle and items purchased comply with federal, state and local regulations. BMS claims no legal federal, state or local certification concerning pollution controlled motor vehicles or mandated emissions requirements. BMS products labeled for use only in competition racing vehicles may only be used on competition racing vehicles operated exclusively on a closed course in conjunction with a sanctioned racing event, in accordance with all federal and state laws, and may never be operated on public roads/highways. Please click here for more information on legal requirements related to use of BMS parts.

  13. #163
    Join Date
    Jun 2012
    Posts
    1,177
    Rep Points
    801.6
    Mentioned
    14 Post(s)
    Rep Power
    9


    Yes Reputation No
    Click here to enlarge Originally Posted by alex@ABRhouston Click here to enlarge
    If you wanted to go driveline brake route- H.A.D. has this down pat.

    I've run their driveline brake products on many 4x4's.
    It will hold a fullsize 4x4 on 40" tires with ease- especially when its in low range, and you have spools/lockers in the differentials.
    http://highangledriveline.com/e_brake.html
    Nice. Thanks for the link. O think mine would have worked, but for the 4lb weight savings it wasn't worth experimenting and some of the risks for me (car rolls away or disk hits something since its down low).

  14. #164
    Join Date
    Nov 2010
    Posts
    404
    Rep Points
    758.8
    Mentioned
    11 Post(s)
    Rep Power
    8


    Yes Reputation No
    RRT Racing did a one-off on my 1M using a 32 row Setrab core.

    Neil

  15. #165
    Join Date
    Jun 2013
    Location
    North Houston
    Posts
    1,295
    Rep Points
    1,639.5
    Mentioned
    111 Post(s)
    Rep Power
    17


    Yes Reputation No
    Click here to enlarge Originally Posted by rudypoochris Click here to enlarge
    Nice. Thanks for the link. O think mine would have worked, but for the 4lb weight savings it wasn't worth experimenting and some of the risks for me (car rolls away or disk hits something since its down low).

    I didn't expect this to be put on a car, just because this setup goes on the back of the transfercase- and appropriately enough, its normally on a truck that is lifter/etc..... and its well tucked away from anything.
    Click here to enlarge
    Burger Motorsports dealer
    Turner Motorsports dealer
    Bimmerworld dealer
    Active Autowerks Dealer
    Shipping built/stroked/CNC ported N54's Internationally!
    Follow us!
    http://www.facebook.com/BMWdoctor
    http://twitter.com/abrhouston
    http://instagram.com/abrhouston/
    http://abrhouston.com
    http://abr.genbook.com Book online appointments!

  16. #166
    Join Date
    Dec 2010
    Posts
    221
    Rep Points
    344.4
    Mentioned
    6 Post(s)
    Rep Power
    4



    3 out of 3 members liked this post. Yes Reputation No

    Engine reassembly has started today

    We washed out everything and started to reassembly the engine. Just a few pictures from he very begining. We use VAC oil buffle as well.
    Attached Images Attached Images     

  17. #167
    Join Date
    Dec 2011
    Location
    Clarksville, TN
    Posts
    3,903
    Rep Points
    2,483.6
    Mentioned
    44 Post(s)
    Rep Power
    25


    Yes Reputation No
    great pics. thanks
    2011 335is DCT, JB4 + MHD BEF, stage 2 LPFP, e50 + 50/50 meth, FBO, MT ET Streets when needed


  18. #168
    Join Date
    Nov 2010
    Posts
    404
    Rep Points
    758.8
    Mentioned
    11 Post(s)
    Rep Power
    8


    Yes Reputation No
    Click here to enlarge Originally Posted by bigdnno98 Click here to enlarge
    great pics. thanks
    +1

    Neil

  19. #169
    Join Date
    Dec 2011
    Location
    Germany
    Posts
    352
    Rep Points
    545.1
    Mentioned
    10 Post(s)
    Rep Power
    6


    Yes Reputation No
    Looks great!
    Current: Audi R8 V10 2013 S-Tronic, daytona grey, carbon side blades, MTM tune, Michelin PSS tires, Capristo x-pipe
    Gone: Audi R8 V10 2010 manual, ice silver, grey side blades, MTM tune, MTM air filters, Michelin PSS tires
    Gone: BMW 335i Individual (Íhlins, PFC brakes, RB turbos etc.)

    Gone: Alpina B3 E46 3,3

  20. #170
    Join Date
    Dec 2010
    Posts
    221
    Rep Points
    344.4
    Mentioned
    6 Post(s)
    Rep Power
    4



    Yes Reputation No

    Engine reassembly

    Still in progress...
    Attached Images Attached Images  

  21. #171
    Join Date
    Dec 2010
    Posts
    221
    Rep Points
    344.4
    Mentioned
    6 Post(s)
    Rep Power
    4



    Yes Reputation No

    VAC Motorsport Oil Pan Buffle is installed

    We use VAC Motorsport Oil Pan Buffle.
    Attached Images Attached Images  

  22. #172
    Join Date
    Dec 2010
    Posts
    221
    Rep Points
    344.4
    Mentioned
    6 Post(s)
    Rep Power
    4



    Yes Reputation No

    Engine reassembly continues

    Today we continued to reassembly the engine...
    Attached Images Attached Images       

  23. #173
    Join Date
    Dec 2011
    Location
    Clarksville, TN
    Posts
    3,903
    Rep Points
    2,483.6
    Mentioned
    44 Post(s)
    Rep Power
    25


    Yes Reputation No
    are you going back with OEM pistons and rods or aftermarket? what about hardware? ARP or OEM?
    2011 335is DCT, JB4 + MHD BEF, stage 2 LPFP, e50 + 50/50 meth, FBO, MT ET Streets when needed


  24. #174
    Join Date
    Dec 2010
    Posts
    221
    Rep Points
    344.4
    Mentioned
    6 Post(s)
    Rep Power
    4



    Yes Reputation No
    Forged Carillo rods, forged JE pistons, ARP.

  25. #175
    Join Date
    Dec 2011
    Location
    Clarksville, TN
    Posts
    3,903
    Rep Points
    2,483.6
    Mentioned
    44 Post(s)
    Rep Power
    25


    Yes Reputation No
    what CR did you go with?

    Click here to enlarge Originally Posted by csl335i Click here to enlarge
    Forged Carillo rods, forged JE pistons, ARP.
    2011 335is DCT, JB4 + MHD BEF, stage 2 LPFP, e50 + 50/50 meth, FBO, MT ET Streets when needed


Page 7 of 19 FirstFirst ... 5678917 ... LastLast

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may post replies
  • You may not post attachments
  • You may not edit your posts
  •