Close

Results 1 to 14 of 14
  1. #1
    Join Date
    Sep 2011
    Posts
    395
    Rep Points
    245.3
    Mentioned
    0 Post(s)
    Rep Power
    3


    Yes Reputation No

    My E46 that had a turbo for a few days...

    Well, i have this E46...

    Click here to enlarge

    I did have a M43B19 motor in it, that i had installed a MHI turbo off a EVO VIII...

    Heads would blow up within 100km each time... gave up after 6 heads...

    Junk motor...

    Click here to enlarge

    So, now i'm installing this stuff:

    Click here to enlarge

    I will keep you guys posted.... i think i might also install S62 plenum on it, and later remote turbo... i was thinking two MHI 16G (one for each bank) would be perfect ?
    Click here to enlarge

  2. #2
    Join Date
    Apr 2010
    Location
    Earth
    Posts
    5,173
    Rep Points
    526.1
    Mentioned
    4 Post(s)
    Rep Power
    6


    Yes Reputation No
    Nice
    Click here to enlargeClick here to enlarge

  3. #3
    Join Date
    Jan 2010
    Location
    SoCal
    Posts
    118,865
    Rep Points
    31,850.6
    Mentioned
    2092 Post(s)
    Rep Power
    319


    Yes Reputation No
    So you are putting an M62 into the E46? Respect. Forced induction on top of that?

  4. #4
    Join Date
    Sep 2011
    Posts
    395
    Rep Points
    245.3
    Mentioned
    0 Post(s)
    Rep Power
    3



    Yes Reputation No
    Click here to enlarge Originally Posted by Sticky Click here to enlarge
    So you are putting an M62 into the E46? Respect. Forced induction on top of that?
    Not really sure on FI.... but have been thinking about sequential MHI 14B or 16G turbos... nothing serious though... just a thought Click here to enlarge
    Click here to enlarge

  5. #5
    Join Date
    Sep 2011
    Posts
    395
    Rep Points
    245.3
    Mentioned
    0 Post(s)
    Rep Power
    3



    Yes Reputation No
    Painting got delayed to the 18th of January, will be mocking up and setting the mounts for the motor in the next days... pictures to come...

    Have aquired TWO MHI 16G (small housing) turbos, but i will be setting everything to "OEM" spec in the engine bay and starting the car before more planning goes on...

    I think the M62TU platform is an excellent one for FI, stock MLS, big con-rod bearings and main bearings, con-rods seem rigid, and because i have the 3500cc and not the 4400cc i have way better cylinder clearance, so i should be able to run 12-15psi on stock head bolts and could even go more crazy with studs !

    Seems i will only need a Intercooler, Injectors and some more fabrication to "slap a turbo on it" Click here to enlarge
    Click here to enlarge

  6. #6
    Join Date
    Nov 2012
    Location
    Naples, Fl
    Posts
    750
    Rep Points
    861.8
    Mentioned
    18 Post(s)
    Rep Power
    9


    Yes Reputation No
    Looks promising, keep us up to date Click here to enlarge
    Click here to enlarge

  7. #7
    Join Date
    Sep 2011
    Posts
    395
    Rep Points
    245.3
    Mentioned
    0 Post(s)
    Rep Power
    3



    Yes Reputation No
    I also have a S62 for parts and have been thinking about installing the ITB and Intake Plenum on the M62, that way i could feed each turbo to each port on the plenum...

    If i get the ME7.2 remapped for "Air Speed Density" or... AlphaN fixed fuel table i see no problems in retrofitting the ITB to the M62 Click here to enlarge
    Click here to enlarge

  8. #8
    Join Date
    Feb 2010
    Location
    NJ
    Posts
    13,468
    Rep Points
    58.0
    Mentioned
    318 Post(s)
    Rep Power
    0


    Yes Reputation No
    very interesting build you have there

  9. #9
    Join Date
    Sep 2011
    Posts
    395
    Rep Points
    245.3
    Mentioned
    0 Post(s)
    Rep Power
    3



    Yes Reputation No
    Delayed the paintjob further, guess i went into focusing on getting the stuff i needed for the swap first, mocking everything 100% up and then i will paint everything...


    So far.... so good:


    Click here to enlarge


    Correct Throttle Pedal and in-sync ECU for motor and EWS :!:
    Click here to enlarge

  10. #10
    Join Date
    Feb 2012
    Location
    Home
    Posts
    142
    Rep Points
    200.4
    Mentioned
    7 Post(s)
    Rep Power
    3


    Yes Reputation No
    Click here to enlarge Originally Posted by angelic0- Click here to enlarge
    If i get the ME7.2 remapped for "Air Speed Density" or... AlphaN fixed fuel table i see no problems in retrofitting the ITB to the M62 Click here to enlarge
    Might be able to help you out with this one.

    Why don't you use your S62?
    Last edited by S62R; 02-24-2013 at 02:16 PM.

  11. #11
    Join Date
    Sep 2011
    Posts
    395
    Rep Points
    245.3
    Mentioned
    0 Post(s)
    Rep Power
    3



    Yes Reputation No
    Click here to enlarge Originally Posted by S62R Click here to enlarge
    Might be able to help you out with this one.

    Why don't you use your S62?
    Egg shaped con-rods.... Click here to enlarge
    Click here to enlarge

  12. #12
    Join Date
    Sep 2011
    Posts
    395
    Rep Points
    245.3
    Mentioned
    0 Post(s)
    Rep Power
    3



    1 out of 1 members liked this post. Yes Reputation No
    Click here to enlarge

    We're here...

    I was going to modify the subframe so that it would clear the pan, but it looks like i will be going to use a BMW X5 (E53) oil pan & pump...

    The only thing that worries me now is that i can not fit a sway bar... have to rethink it at least...

    I've been test fitting the motor and will start by using a 5HP24 transmission and a 4.44 ratio differential (168mm, let's see how long it holds)

    I've already fixed the pinout for the ECU and wired in the electronic throttle pedal... everything should fire right up once the motor and tranny have been fitted in Click here to enlarge
    Click here to enlarge

  13. #13
    Join Date
    Jan 2010
    Location
    SoCal
    Posts
    118,865
    Rep Points
    31,850.6
    Mentioned
    2092 Post(s)
    Rep Power
    319


    Yes Reputation No
    Click here to enlarge Originally Posted by angelic0- Click here to enlarge
    http://www.bimmerboost.com/images/im...456190_n-1.jpg

    We're here...

    I was going to modify the subframe so that it would clear the pan, but it looks like i will be going to use a BMW X5 (E53) oil pan & pump...

    The only thing that worries me now is that i can not fit a sway bar... have to rethink it at least...

    I've been test fitting the motor and will start by using a 5HP24 transmission and a 4.44 ratio differential (168mm, let's see how long it holds)

    I've already fixed the pinout for the ECU and wired in the electronic throttle pedal... everything should fire right up once the motor and tranny have been fitted in Click here to enlarge
    We need clearer pics!

    Stage 2 or 2.5 E9X M3 S65 V8 supercharger kit for sale
    : http://www.boostaddict.com/showthrea...r-kit-for-sale

  14. #14
    Join Date
    Sep 2011
    Posts
    395
    Rep Points
    245.3
    Mentioned
    0 Post(s)
    Rep Power
    3



    Yes Reputation No
    More pics will be posted up once i get a few things sorted...
    Click here to enlarge

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may post replies
  • You may not post attachments
  • You may not edit your posts
  •