Search:

Type: Posts; User: geshsoft

Search: Search took 0.01 seconds.

  1. Replies
    12
    Views
    275

    Well, I do not know where they plan to get the...

    Well, I do not know where they plan to get the 9HP to power the compressor. What I typed above is just an idea. Since they are still using conventional turbos I'd guess they do not recycle energy the...
  2. Replies
    12
    Views
    275

    Coming to think of it, turbochargers recycle some...

    Coming to think of it, turbochargers recycle some exhaust energy at the expense of increased backpressure. Also, and correct me if I am wrong, the main reason why the turbochargers are as close as...
  3. Replies
    5
    Views
    251

    I thought I'd update the thread - I fixed the AC...

    I thought I'd update the thread - I fixed the AC and sure enough it turned out that the high side hose (superseded by P/N 64539239768) had developed a pinhole from rubbing against a stainless steel...
  4. Replies
    5
    Views
    251

    I think what I'll end up doing is removing the...

    I think what I'll end up doing is removing the filter box and intake tubing, maybe even FMIC. The more I look at it the more I wonder if it is really the hose I think it is or P/N 64509163320. I...
  5. Replies
    5
    Views
    251

    High Pressure AC hose leak

    I recently found out my AC is not blowing cold air anymore, even-though the compressor turns on. After a bit of poking under the hood I found out that my high pressure hose P/N 64539239768 is...
  6. Actually I misspoke - I am on the AT bandwagon....

    Actually I misspoke - I am on the AT bandwagon. Sorry for the confusion. I am still looking into getting one after the positive reviews.
  7. Waiting for reviews. If all looks good then I'll...

    Waiting for reviews. If all looks good then I'll be getting one. :pop:
  8. Replies
    88
    Views
    2,547

    LOL

    LOL
  9. Replies
    88
    Views
    2,547

    Just for the record DES is actually weak compared...

    Just for the record DES is actually weak compared to current 128 bit and higher encryption. The CCA (circuit card assembly) on the picture is done with FPGAs as GPUs and broadband were not as...
  10. Replies
    88
    Views
    2,547

    Yep, I doubt it happened.

    Yep, I doubt it happened.
  11. Replies
    88
    Views
    2,547

    Defeating modern encryption by brute force is not...

    Defeating modern encryption by brute force is not that easy, especially if it happens to be 128 bit and above with a good cypher. I would rather believe that someone in the proper position leaked the...
  12. Replies
    88
    Views
    2,547

    Similar situation here. I could find some time to...

    Similar situation here. I could find some time to design and build it, but I don't really have the resources or the time to figure out the CAN message set and experiment as I am not in the car...
  13. Replies
    88
    Views
    2,547

    Following all the AT threads here I am getting...

    Following all the AT threads here I am getting the impression that, as insane as it sounds, designing a TCM from scratch may not be too big of a deal, at least not on the hardware side, compared to...
  14. Replies
    8
    Views
    292

    6HP21 CAN message set

    So, from what I've read on this forum no one has been able to defeat the encryption of the 6HP21 TCM. However, has anyone logged and understood all or most of the CAN messages associated with the TCM?
  15. Replies
    7
    Views
    302

    Is this achieved by adaptation reset with say...

    Is this achieved by adaptation reset with say INPA? I am asking as in INPA it's simply stated "reset adaptations" or something similar without going into much detail.
    I am about to replace the...
  16. Replies
    12
    Views
    614

    Are you asking about the transmission firmware...

    Are you asking about the transmission firmware version or something else? Is it something I can check with INPA?
  17. Replies
    12
    Views
    614

    I know what you mean. The procedure I mentioned...

    I know what you mean. The procedure I mentioned is only initial. The transmission actually took quite a bit longer to smooth out. I have to admit that I've been driving like a granny for couple...
  18. Replies
    12
    Views
    614

    I used INPA. I've done it also with the BT tool.

    I used INPA. I've done it also with the BT tool.
  19. Replies
    12
    Views
    614

    I reset and followed the re-adaptation procedure...

    I reset and followed the re-adaptation procedure for 6HP19:


    4 to 6 slow pulls from full stop up to 4th gear and cruse down to stop with brakes applied at the end in D to adapt clutch packs for...
  20. Replies
    12
    Views
    614

    ..and I thought I am unique... :D Joke...

    ..and I thought I am unique... :D

    Joke aside...



    The whiplash shifting down to 1 happens to me, as well, but only if I am braking right post down shift not leaving the car to cruise down to...
  21. Replies
    12
    Views
    614

    6HP21 erratic shifting behavior

    Hi,
    I have a AT 335i '07 and my transmission has been acting up lately. The issues are usually prolonged settling 2-3 upshift which results in slight whip like (backlash) behavior under low...
  22. Replies
    28
    Views
    6,774

    Sticky: All true. I see you have a 335i '07. Have you...

    All true. I see you have a 335i '07. Have you experienced any transmission issues, such as prolonged 2-3 transition in both D and DS modes and harsh shifts in DS mode? I am having 335i '07 myself and...
  23. Replies
    28
    Views
    6,774

    Sticky: Good point about INPA considered dealer software....

    Good point about INPA considered dealer software. The part that really bothers me is mentioned in the Sonnax Technical Booklet under electronics:

    "The TCM is capable of limited solenoid adaptation...
  24. Replies
    28
    Views
    6,774

    Sticky: Hi, So I've been a lurker for couple months on...

    Hi,
    So I've been a lurker for couple months on this forum as I am afraid I don't have much to bring on the table compared to a lot of people here.
    On the topic - I've read all the documents posted...
Results 1 to 24 of 24