Close

Search:

Type: Posts; User: Jeffman

Page 1 of 11 1 2 3 4

Search: Search took 0.01 seconds.

  1. I thought the load per gear tables were mainly...

    I thought the load per gear tables were mainly used by the manual transmission guys? Mine is zeroed out and I only use load per rpm.
    Let me know how you make out with both tables in play.
  2. Hi Brad, I've been working on a similar problem...

    Hi Brad,
    I've been working on a similar problem with Martial over the last few weeks (he's now off a few weeks en vacance). I thought this may be a MHD logic glitch but now I'm not sure. Still a...
  3. Impressive!

    Impressive!
  4. What ever happened with this intake manifold?

    What ever happened with this intake manifold?
  5. Replies
    182
    Views
    15,389

    +1!

    +1!
  6. Replies
    182
    Views
    15,389

    1.15 bar

    1.15 bar
  7. Also note that I NEVER had gone WOT until oil...

    Also note that I NEVER had gone WOT until oil reached 210F...that's what the BMW manual advised and I've been following that advice religiously since day 1 eight years ago.
  8. I'm no statistician but shouldn't we also poll...

    I'm no statistician but shouldn't we also poll people who have no rod bearing problems (yet)?



    Which N54 car do you drive (Model and Transmission)
    - 2008 E90 AT Xi. I'm the original owner...
  9. Replies
    31
    Views
    2,812

    :handgestures-thumb: Thanks.

    :handgestures-thumb: Thanks.
  10. Replies
    31
    Views
    2,812

    ^ This worked. I adjusted my scaled load values...

    ^ This worked. I adjusted my scaled load values in L2T 1, 2, 3 to be a little higher. Apparently I made them too low. No more "Torque Lim Active" = 4.0...they are all clear zeroes....
  11. Replies
    31
    Views
    2,812

    Since we are scaled, shouldn't the load axes in...

    Since we are scaled, shouldn't the load axes in the three Load to Torque tables also be scaled? Maybe that's what's causing my Torque Limit Active = 4 results. Since I'm targeting Load = 175, and...
  12. Replies
    31
    Views
    2,812

    RSL, more tinkering. My car seems to be dialed...

    RSL, more tinkering. My car seems to be dialed pretty well into lean spool. I lowered my loads a little and increased my BLM per gear to above 2.0. Boost is increasing more smoothly but now I'm...
  13. Replies
    31
    Views
    2,812

    V8Bait A little help, please? All of my searches...

    V8Bait A little help, please? All of my searches point to JB4 questions or old Cobb questions. I'm MHD flash only with MBoost. Thanks
  14. Replies
    31
    Views
    2,812

    Thanks for your comments, @RSL...

    Thanks for your comments, @RSL.
    Here are two additional data points from my map for your consideration:
    1. My WGDC limit is indeed set to 80. I do not know why it's pegging 96+ ???
    2. I had...
  15. Replies
    31
    Views
    2,812

    Should I adjust my MAF axis in my BLM and BLM by...

    Should I adjust my MAF axis in my BLM and BLM by Gear tables?

    Here is my current table BLM by Gear table
    :MAF: 194 236 267 277 281 296 310 ...
  16. Replies
    31
    Views
    2,812

    Thanks for the good advice, RSL. I'll give this a...

    Thanks for the good advice, RSL. I'll give this a try.
    I tried repping you but apparently had already done so recently. :eusa-clap:
  17. Replies
    182
    Views
    15,389

    I found the thread about rescaling the load axis....

    I found the thread about rescaling the load axis. I generally rescaled the load value breakpoints over 150 for each table by about 50%, the idea being that a load of 185 with the rescaled TMAP...
  18. Replies
    182
    Views
    15,389

    Update: Looking at the XDF posted in May 2016 by...

    Update: Looking at the XDF posted in May 2016 by Jake in TunerPro, here are the tables which have a load axis:
    Fuel - Bank 1, 2, Spool
    Fuel Scalar - Bank 1, 2
    Timing - Fail Safe, Main, Open Loop,...
  19. Replies
    182
    Views
    15,389

    Boost ceiling = 1.5 bar I'm poking around those...

    Boost ceiling = 1.5 bar
    I'm poking around those tables now, which I still need to rescale. Which load axis, which tables?
  20. Replies
    31
    Views
    2,812

    I'm also very interested in using my 3 column...

    I'm also very interested in using my 3 column scaled 3.5 bar N20 TMAP sensor to control the ECU efficiently in the 22-24 psi range. Elsewhere on this forum I'm being told I need to also rescale my...
  21. Replies
    182
    Views
    15,389

    Which tables with load need to be rescaled?

    Which tables with load need to be rescaled?
  22. Any update? My transmission just slipped > 500...

    Any update? My transmission just slipped > 500 ft-lb.
  23. Replies
    182
    Views
    15,389

    The power gain is insane...400 HP/520 ft-lb...

    The power gain is insane...400 HP/520 ft-lb (virtual Dyno in 4th gear...go ahead and download my crazy log posted in this thread).
    I have no idea how long they would last doing this. The...
  24. Replies
    182
    Views
    15,389

    I understand the "I need to lower my load"...

    I understand the "I need to lower my load" comment by Jake a few days ago, above. What's really interesting is my current map is based on an unscaled boost map which was reaching loads of about 200...
  25. Replies
    182
    Views
    15,389

    I have no idea how "safe" it is. Only been doing...

    I have no idea how "safe" it is. Only been doing it a few times this past week.
Results 1 to 25 of 252
Page 1 of 11 1 2 3 4