Close

Search:

Type: Posts; User: andy_divers

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    94
    Views
    3,315

    I guess I've just assumed, but doesn't a cut...

    I guess I've just assumed, but doesn't a cut cylinder from a misfire turn off the injector AND coil? Since when does a manufacturer leave a coil on if it thinks it cant fire. Seems like a good way to...
  2. Replies
    94
    Views
    3,315

    That's is knock (maybe heat related). The tips of...

    That's is knock (maybe heat related). The tips of the valve pockets are even melted. Probably turned your injector tip into a glow plug lol
  3. I don't see why you couldn't

    I don't see why you couldn't
  4. Mounts are the same. Silicone heat shield is the...

    Mounts are the same. Silicone heat shield is the difference
  5. You're not taking a 31mm comp plus valve with...

    You're not taking a 31mm comp plus valve with 75lb springs to 10k on a high boost turbo car. Maybe 9-9.5k if the ramp is mild and BP is low.... been there
  6. Replies
    290
    Views
    16,165

    I'm not sure either. Like I said, there are only...

    I'm not sure either. Like I said, there are only three n54 kits every produced and that isn't one of them. Someone sold him a S6 to run a n54 via piggyback.

    I'd like to see pictures. Let's see if...
  7. Replies
    290
    Views
    16,165

    He's not "testing" anything. It's not a n54 kit....

    He's not "testing" anything. It's not a n54 kit. He just bought a Syvecs s6.
  8. Replies
    290
    Views
    16,165

    That's between you and garth, but I can tell you...

    That's between you and garth, but I can tell you without a doubt you do not own a pnp n54 syvecs unit.

    Take a picture of it. I assume you still have the dme in the car without having piezo...
  9. Replies
    290
    Views
    16,165

    Njz You do not have a Syvecs N54 pnp kit. You...

    Njz You do not have a Syvecs N54 pnp kit. You have a 3rd party Syvecs S6 as a piggyback.

    There are only 3 Syvecs N54 pnp units in existence. I have one, Jake at motiv has one, and the other is on...
  10. When I say, "stock converter" I mean the...

    When I say, "stock converter" I mean the cover/body of the stock stamped steel converter. The guts needed to handle power may fit in the stock core, but the cover itself will probably be limiting.
  11. So who is building the custom converters? The...

    So who is building the custom converters? The stock converter even with new guts is less than adequate for 1000+. If you manage to build (and control) a 1000+hp trans you're still stuck with the...
  12. Replies
    290
    Views
    16,165

    Here's an update from my side... We have had...

    Here's an update from my side...

    We have had the syvecs on n54s slowly playing with it. My personal hurdles and hang-ups have been a few bugs that are over my head to troubleshoot and my learning...
  13. Replies
    28
    Views
    3,493

    Not necessarily if you're running any current...

    Not necessarily if you're running any current production lpfp system.
  14. Battle of the 6870's at Oregon shift sector ;)

    Battle of the 6870's at Oregon shift sector ;)
  15. Replies
    17
    Views
    1,925

    That's what I'm saying. Either do it in the map...

    That's what I'm saying. Either do it in the map or the check box, not both correct? (Just like map sensor calibration)
  16. Replies
    17
    Views
    1,925

    I have not used the adv sensors so correct me if...

    I have not used the adv sensors so correct me if I'm wrong, but you flash a map with the cal for them AND selected the adv box in mhd? Doesn't that stack two cals on top of eachother?
  17. Replies
    51
    Views
    5,701

    I sell a kit ;)...

    I sell a kit ;)
    http://www.ad-eng.net/store/p33/ADE_335i_Rear_Drag_Brake_Kit.html
  18. A loose engine makes less noise once hot.......

    A loose engine makes less noise once hot.... shocker ;)
  19. Replies
    406
    Views
    20,661

    That is another rumor I'd like to see any proof...

    That is another rumor I'd like to see any proof of.... I have never tapped and plugged the ports on heads and have run tons of n54s at tons of boost and have NEVER seen this magical "valve cover...
  20. Replies
    90
    Views
    8,873

    I am against assumptions. People assume that an...

    I am against assumptions. People assume that an open deck block is problematic and a closed deck is the solutions. 99% of people saying this are just repeating what they read and have no first hand...
  21. Replies
    90
    Views
    8,873

    What if I told you I've made 300+whp per cylinder...

    What if I told you I've made 300+whp per cylinder on an open deck sleeved block without issue? Go get some experience. Stop repeating what you've been "told".
  22. On a spun bearing, I'd want to know the fuel,...

    On a spun bearing, I'd want to know the fuel, oil, interval, and what the top of the piston and plugs look like.... then and leak down to check the ring to wall sealing.

    Trend of n54 bearing...
  23. Replies
    11
    Views
    2,204

    Pan, tray, pickup, a few pan and tray bolts,...

    Pan, tray, pickup, a few pan and tray bolts, coolant pipe, thermostat housing(depending), hpfp line, mounts, and flywheel will all need to be transferred
  24. Replies
    406
    Views
    20,661

    Apples to oranges... my fitting is a plug, not a...

    Apples to oranges... my fitting is a plug, not a pcv valve.

    Why is there so much emphasis on having a vacuum source to the crankcase at idle and low load?! Focus on the real goal, which is to...
  25. Replies
    25
    Views
    3,665

    You can't compare the old 58mm with the 6062...

    You can't compare the old 58mm with the 6062 gen2. The 6062gen2 is what you want. It will out spool AND out power a 6262... it's a bad $#@!!
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4