Search:

Type: Posts; User: Terry@BMS

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    38
    Views
    638

    S63/S63TU: Email for any specific questions. I don't check...

    Email for any specific questions. I don't check this forum as often as I should!

    But the setting change is due to the s63's 3.5 bar MAP sensors.
  2. Replies
    38
    Views
    638

    S63/S63TU: Dyno runs in 5th gear end at 6200rpm. While runs...

    Dyno runs in 5th gear end at 6200rpm. While runs in 4th gear can go to redline.
  3. Replies
    16
    Views
    231

    S63/S63TU: It's just part of the lame DCT torque management...

    It's just part of the lame DCT torque management logic. Our N55 135i DCT does the same thing at 280whp or 390whp if you start the run at 2000rpm. But not if you start it at 1500rpm. The dyno trick to...
  4. Replies
    16
    Views
    231

    S63/S63TU: It's a DCT car. The DME sometimes holds back...

    It's a DCT car. The DME sometimes holds back boost in the midrange for those in dyno situations. It depends on the RPM you floor it at and whether you roll in to the gas or just floor it.
  5. Replies
    16
    Views
    231

    S63/S63TU: Due to the low volume we're not going to release...

    Due to the low volume we're not going to release a meth kit specific to the x63 motor. But to get meth workong on the x63 platform is relatively easy. You just need a Stage2 board, this special...
  6. Replies
    16
    Views
    231

    S63/S63TU: These runs were at ~21psi. I think at ~23psi it...

    These runs were at ~21psi. I think at ~23psi it would break 700rw. We'll continue working on it as time permits.
  7. Replies
    99
    Views
    2,430

    +1!

    +1!
  8. Replies
    99
    Views
    2,430

    CPS2500 to 1 for twin scroll, and DWP to 40 to...

    CPS2500 to 1 for twin scroll, and DWP to 40 to get the PWM scaling right for a twin scroll.
  9. Replies
    99
    Views
    2,430

    It's just various squiggly lines. I'll let P...

    It's just various squiggly lines. I'll let P share the fine details & results. But I think it ran pretty well on conservative tuning. His clutch and DMFW is holding it back big time.

    Not to toot...
  10. Replies
    99
    Views
    2,430

    Log from the dyno earlier today. :)

    Log from the dyno earlier today. :)
  11. Replies
    16
    Views
    231

    S63/S63TU: M5 Meth Testing

    Was able to take a few runs on the dyno today. Meth kit added around 25-30whp over the previous race gas mix! Maybe a new dynojet s63 record? I'll have to VBOX it soon to see how these dyno gains...
  12. Seems to be a ton of single turbo stuff coming...

    Seems to be a ton of single turbo stuff coming out lately. I wish someone would develop a viable high pressure pump upgrade. Meth is great but having to rely on it for fueling is holding us back.
  13. Smokes like a chimney sometimes. Probably a...

    Smokes like a chimney sometimes. Probably a busted ring/piston. Ran it at full power with a sealed PCV accidentally which seems to have hastened its demise. But with a 6466 and OEM pistons these...
  14. Replies
    17
    Views
    427

    S63/S63TU: Yes the M5 was not running that well at the...

    Yes the M5 was not running that well at the event. Best 60-130 on race day was only 8.2s. :( Maybe the weather or maybe the old can of race gas I had sitting in the garage wasn't as potent as I...
  15. I wish FFTEC would hurry up with our E92 short...

    I wish FFTEC would hurry up with our E92 short block! :)
  16. Replies
    99
    Views
    2,430

    Yes 100 octane unleaded! Looking forward to...

    Yes 100 octane unleaded!

    Looking forward to SS myself. The ST 135i *should* be ready. As a backup plan I just put a meth kit in the M5. Ando @ BMS should be there with his new FFTEC 58 bottom...
  17. Replies
    175
    Views
    5,197

    No updates yet.

    No updates yet.
  18. Replies
    99
    Views
    2,430

    1=~125 psi.

    1=~125 psi.
  19. Replies
    99
    Views
    2,430

    High fuel pressure looks bad. Time to dump the...

    High fuel pressure looks bad. Time to dump the E85 and switch to race gas.
  20. Replies
    99
    Views
    2,430

    It adjusts itself. You can also view it in the...

    It adjusts itself. You can also view it in the CSV header.
  21. Replies
    99
    Views
    2,430

    For any log you'd want to look at PWM. You can...

    For any log you'd want to look at PWM. You can raise FF to raise PWM further, but at such a low target and high PWM, I'd guess you have a WG line issue. It should be configured using the top and...
  22. Replies
    99
    Views
    2,430

    Can't wait to see how it does on the dyno. You...

    Can't wait to see how it does on the dyno. You can experiment with E85 but at higher power levels it's sketchy. Might make sense to dyno tune it for straight 100 unleaded only to start.
  23. Replies
    38
    Views
    638

    S63/S63TU: The CAN Tool is not going to block a CEL from...

    The CAN Tool is not going to block a CEL from coming up. If you get a CEL, read it using a BT cable, and use the code to resolve the physical issue with the vehicle.
  24. Replies
    39
    Views
    687

    Single turbo setup can be a little bit of a...

    Single turbo setup can be a little bit of a headache party because everyone is using different kits but everything one needs to tune it is out there. Important "steps" (in my opinion) are getting it...
  25. Replies
    38
    Views
    638

    S63/S63TU: That's certainly possible. Were you the guys who...

    That's certainly possible. Were you the guys who installed it on the MAF instead of the MAP and fried the box? :) If so I know a new box was sent along for it.

    Clear all codes and see what you can...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4