Search:

Type: Posts; User: Tomaz

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    1,129
    Views
    43,733

    I want 600-630rwhp and spool at 3500-3700, thats...

    I want 600-630rwhp and spool at 3500-3700, thats all what I need.
    700-800-900rw is overkill for me, no traction till 200kmh...
    What you advise to me? ?
  2. Replies
    1,129
    Views
    43,733

    Is it better for spool/power then GTX3582r?

    Is it better for spool/power then GTX3582r?
  3. Replies
    32
    Views
    1,800

    I am that lucky man :music-rockout:.

    I am that lucky man :music-rockout:.
  4. You will be able to read this code only with...

    You will be able to read this code only with INPA, and it saves only in the history at transmission.

    Usually it is a code 4F86 [20358] "Ratio-Monitoring Symptom Circuit-Monitoring".
  5. Replies
    28
    Views
    885

    03.2007 EU, but my diff is 2008.

    03.2007 EU, but my diff is 2008.
  6. Replies
    28
    Views
    885

    MT shaft already installed on my 6AT car, it's...

    MT shaft already installed on my 6AT car, it's 100% compatible.
  7. Replies
    28
    Views
    885

    MT's is little thicker. I had installed this...

    MT's is little thicker. I had installed this shaft after my AT failed.
    It's 100% interchangeable, trust me!

    MT shaft: 33207568731


    LK=86MM/D=38MM
  8. Replies
    28
    Views
    885

    Shafts from MT are interchangeable with AT. At me...

    Shafts from MT are interchangeable with AT. At me one shaft from MT is a little thicker, than from AT.
  9. Replies
    16
    Views
    646

    Fixed! This is Drive Belt Tensioner! I had...

    Fixed! This is Drive Belt Tensioner!
    I had sprayed WD40 on it and the noise was gone!
  10. Replies
    16
    Views
    646

    Forged, CR 9.5.

    Forged, CR 9.5.
  11. This is better comparison! 28559

    This is better comparison!
    28559
  12. Replies
    16
    Views
    646

    My VANOS corrections, 8.1 intake and 7.3 exhaust....

    My VANOS corrections, 8.1 intake and 7.3 exhaust.
    28558
  13. Replies
    16
    Views
    646

    Stop, stop. Engine block is bored/honed ...

    Stop, stop. Engine block is bored/honed properly, I personally measured everything. All spare parts new, including the crankshaft, rods, pistons etc.
    This sound is only after long parking and in...
  14. Replies
    16
    Views
    646

    Yes, this is 335i.

    Yes, this is 335i.
  15. Replies
    16
    Views
    646

    Cold start rattle or pistons clap?

    Hello guys!
    Last summer I made engine rebuild with CP pistons (clearance0.0035") and everything was good.
    But in the winter when it is cold 0C and below, at morning cold start there is a sound...
  16. I hope that no more than 2 month.

    I hope that no more than 2 month.
  17. Replies
    13
    Views
    636

    The 1st one have interface and you can adjust...

    The 1st one have interface and you can adjust parameters.
    28287
  18. Replies
    13
    Views
    636

    One more device!...

    One more device!
    http://moretraction.com/Products_Drag.htm

    With the awful price...
  19. Replies
    13
    Views
    636

    There are no problems, I did it for our general...

    There are no problems, I did it for our general needs. I read this forum every day, but nothing write. My English not strong so much. :rolleyes:
  20. Replies
    13
    Views
    636

    I will be happy, but it's interesting with Cobb...

    I will be happy, but it's interesting with Cobb flash too.
  21. Replies
    13
    Views
    636

    Cobb + traction control

    Hello guys!

    I found an interesting device, its work is based on the principle of ignition retard, like Vishnu TC.
    28285
    How it's work:

    Traction controler - the electronic device allowing on...
  22. Replies
    53
    Views
    1,827

    I think, I need open my engine...

    I think, I need open my engine again!:angry-banghead:
  23. Replies
    53
    Views
    1,827

    Hi guys! I have a problem with a smoke, misfires...

    Hi guys!
    I have a problem with a smoke, misfires and oil in spark plugs, but it's not turbos and it occurs periodically.
    I have done compression and leak down test. All cylinders is the same...
  24. Replies
    23
    Views
    846

    I have INPA, but i don't have this injector menu....

    I have INPA, but i don't have this injector menu. What's version you have?
  25. Replies
    726
    Views
    25,439

    It doesn't matter. Electrical hardware identical...

    It doesn't matter. Electrical hardware identical also it is possible to load any software.
    If you receive error when loading, try once again.
Results 1 to 25 of 86
Page 1 of 4 1 2 3 4