Search:

Type: Posts; User: JoshBoody

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    160

    For Sale: $175 shipped to 48 states

    $175 shipped to 48 states
  2. Replies
    3
    Views
    160

    For Sale: Custom Cold Air Intake... Mr5 Style

    Simple and secure construction. Bracket included for relocating PS pump res.
    2.5" hose mounted to airbox flange by outside clamp... so no possibility of loose fasteners.

    $200
  3. Replies
    83
    Views
    2,856

    Octane is the primary factor in MBT. Even if you...

    Octane is the primary factor in MBT. Even if you were past optimum peak pressure (likely not the case at 15deg adv in the top), but had the octane, there would be no engine damage. 15deg could work...
  4. Replies
    5
    Views
    327

    For Sale: sold, can delete

    sold, can delete
  5. Replies
    6
    Views
    185

    You will only be "blown away" again with e85,...

    You will only be "blown away" again with e85, race gas, or meth.
  6. What I meant above is that with the solid motor...

    What I meant above is that with the solid motor mounts engine doesn't move and tranny removal becomes much more difficult. Many don't consider this until they have to pull it. Just something else to...
  7. Replies
    449
    Views
    16,286

    Took a pic of whiskey I had yesterday... Loved it...

    Took a pic of whiskey I had yesterday... Loved it and 59% alcohol! No idea of the cost.
  8. Another neg to solid mounts many don't...

    Another neg to solid mounts many don't consider... Tranny is more difficult to remove. Could be considerably more difficult.
  9. Replies
    5
    Views
    346

    I'd think you can flash over vishnu without...

    I'd think you can flash over vishnu without worry. But you can read it and compare in TP beforehand to be sure... this will confirm the ROM was not altered.

    I have a 08 built 10/07 with msd80 and...
  10. Replies
    5
    Views
    341

    For Sale: Helix sold

    Helix sold
  11. Replies
    11
    Views
    340

    There's an interesting thread on E90 where flash...

    There's an interesting thread on E90 where flash tune pegged STFT due to -LTFT running 17:1+ for half the pull until LTFT came back... no DME reaction, which seems to be typical. If piggy had a lean...
  12. Replies
    5
    Views
    341

    For Sale: I did buy it used, and put

    I did buy it used, and put <10k miles. AFAIK, no dings or dents but I didn't look over it very thoroughly... its all packaged up now. I did pressure test it with no leaks and rinsed it with acetone...
  13. Replies
    5
    Views
    327

    For Sale: 2008 E90 335i Sports pkg MT $17,000

    2008 E90 MT for sale.
    Mileage 79,000mi
    location: Phoenix, AZ

    I have owned the car since 2009 and 32k miles. Has always been garaged.

    Koni FSD shocks/struts with 15k mi
    New stoptech...
  14. Replies
    5
    Views
    341

    For Sale: Helix FMIC and Mr5 Custom CAI

    Helix: $500
    Mr5 Intake $200

    Helix: pressure tested to 25psi, no leaks. New clamps: 3 t-bolt and 1 worm... the worm is better for the cold side top hose due to clamp area.

    Mr5 intake is 2.5"...
  15. Replies
    342
    Views
    16,023

    N54 can smoke fairly easily... maybe improved oil...

    N54 can smoke fairly easily... maybe improved oil flow would help this. I like all the thought put into this build.
  16. Replies
    20
    Views
    591

    yep, very strange... seen this a couple times,...

    yep, very strange... seen this a couple times, but not to this degree I think. OP i'd be curious to see a log at various loads/throttle for a similar rpm range. And remove some of the timing...
  17. Replies
    51
    Views
    1,388

    I agree that increased duration probably won't...

    I agree that increased duration probably won't help much... as long as VANOS is tuned properly. Lift will help. Hell you could decrease duration and increase the lift slope (with right valvetrain) to...
  18. BP/EGT are directly related to boost, so as long...

    BP/EGT are directly related to boost, so as long as you can maintain target boost you are basically ok. At some point (maybe this point is fairly early) the housing/manifold can't accommodate the...
  19. As long as your exhaust post-turbo can support...

    As long as your exhaust post-turbo can support the HP, BP won't change. The extra air mass just bypasses through the WGs. Terry has prob seen more n2o logs then most... I'd be curious to see the WGDC...
  20. Replies
    61
    Views
    1,671

    Time for a leak down test. I doubt it's...

    Time for a leak down test. I doubt it's DME/coil... you have to have fire to have knock (which is a very specific freq).

    You have a log with ST trims. I'm curious about my BP theory. Bank 2 would...
  21. Replies
    426
    Views
    11,319

    The HPFP can move Xcfm fuel from the chamber to...

    The HPFP can move Xcfm fuel from the chamber to rail with each rotation… increase the rotations = more volume. The actual increase “should” be somewhat linear. The higher speed could be outside the...
  22. Replies
    61
    Views
    1,671

    Swapping knock sensors is interesting, but these...

    Swapping knock sensors is interesting, but these are pretty simple devices and can't see how it could just effect 1 cyl... unless its the reluctor.

    Do you have a RB PCV valve? Maybe clean the VC...
  23. I read this sometime ago and was a little...

    I read this sometime ago and was a little surprised at the vid outcome. Need to look at the HP curve factoring gear ratios to get avg HP... this is the bottom line in a roll (along with weight and...
  24. theres 2 screens. 1 you can directly enter an...

    theres 2 screens. 1 you can directly enter an rpm, but it resets when cars off. The 2nd permenently changes idle speed, but not obvious (i have German version). The adjustment values do not directly...
  25. Replies
    61
    Views
    1,671

    Have to use good technique with seafoam... most...

    Have to use good technique with seafoam... most important part IMO is at the end of the can let the motor ingest a bunch and stall. Let it sit off for 30min (the thought is that its soaking into the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4