Close

Search:

Type: Posts; User: OlegD

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    83
    Views
    6,249

    M50/52 + S50/52: The parts are glued together into a coherent...

    The parts are glued together into a coherent shell.
    4722547226
    I've got glossy surface inside.
    4722747228
    I also want to to paste reinforcing rings on ends.
    I applied recent reinforcing layers...
  2. Replies
    83
    Views
    6,249

    M50/52 + S50/52: I continue.. 471954719647197. All internal...

    I continue..
    471954719647197.
    All internal surfaces are coated with a layer of epoxy resin:47198
    I picked up carbon first time. I like the result!! Parts are very light and strong...
  3. Replies
    83
    Views
    6,249

    M50/52 + S50/52: Hmm...The result was not so bad as I...

    Hmm...The result was not so bad as I thought!!:music-rockout:
    47191
    Tomorrow I cut the shell and take out model. Then I glued together parts of the shell and topped with another 2-4 layers of...
  4. Replies
    83
    Views
    6,249

    M50/52 + S50/52: Since September I was preparing the model of...

    Since September I was preparing the model of inlet piping from filter to compressor part of turbocharger. It will be made of carbon by vacuum infusion :music-rockout:....
  5. Replies
    83
    Views
    6,249

    M50/52 + S50/52: Also I finished to weld exhaust...

    Also I finished to weld exhaust pipes.47075470764707747078
    :naughty:
  6. Replies
    83
    Views
    6,249

    M50/52 + S50/52: I have some news. Last spring I did what I had...

    I have some news. Last spring I did what I had planned for a year! I designed and built my own twin-mass flywheel with two organic clutch discs and dampers!! All parts were precision machined by my...
  7. Replies
    83
    Views
    6,249

    M50/52 + S50/52: Thanks.This month I'm at work in Moscow. I will...

    Thanks.This month I'm at work in Moscow. I will continue to engage with machine in November. Tomorrow I takin away carbon fiber triaxial sleeving, it had come from California.
  8. Replies
    83
    Views
    6,249

    M50/52 + S50/52: To Admin: Please remove excess duplicate message...

    To Admin: Please remove excess duplicate message #72 :angry-banghead:
  9. Replies
    83
    Views
    6,249

    M50/52 + S50/52: Some photos of the process. At last I got the...

    Some photos of the process.
    At last I got the rear muffler and now I can finally finish exhaust:
    45476454754547145470
    The engine is fully assembled, camshafts are aligned with my device:...
  10. Replies
    83
    Views
    6,249

    M50/52 + S50/52: The engine is assembled and it is necessary to...

    The engine is assembled and it is necessary to adjust the valve clearances. Vanos renovated. 2 Last week I was engaged in a high-pressure pipes and a private design of the air filter....
  11. Replies
    83
    Views
    6,249

    M50/52 + S50/52: The fastest work of Chinese:music-rockout:...

    The fastest work of Chinese:music-rockout:
    434344343543436
  12. Replies
    83
    Views
    6,249

    M50/52 + S50/52: I spent a lot of time thinking about filtering...

    I spent a lot of time thinking about filtering the air. A simple solution with K&N filter require a minimum of 2 KN filter model RG-1002RD, and I even bought. But I like my original design with two...
  13. Replies
    83
    Views
    6,249

    M50/52 + S50/52: Some photos of progress: ...

    Some photos of progress:
    4327043281432804327943278432774327643275432744327343272432714328343282
    Some time ago were bought:

    Link G4+ Xtreme
    Aeromotive Adjusatable Fuel Pressure Regulator -6 In...
  14. Replies
    83
    Views
    6,249

    M50/52 + S50/52: mm3 Thank You!!!:music-rockout:

    mm3 Thank You!!!:music-rockout:
  15. Replies
    83
    Views
    6,249

    M50/52 + S50/52: Pipes of the exhaust manifold is not equal...

    Pipes of the exhaust manifold is not equal length, but optimal. I have long calculated the motion sequence of pulses, their sum, and at least in the calculation was quite a good pulses combination....
  16. Replies
    83
    Views
    6,249

    M50/52 + S50/52: :think:Wait for the final result!

    :think:Wait for the final result!
  17. Replies
    83
    Views
    6,249

    M50/52 + S50/52: thanks,I saw these parameters. But Piston kit...

    thanks,I saw these parameters. But Piston kit contains a unique paper sheet.
  18. Replies
    83
    Views
    6,249

    M50/52 + S50/52: Sirs, Does anyone have a specification sheet on...

    Sirs,
    Does anyone have a specification sheet on 289074 JE pistons for S50B32? I lost mine. I need to know the exact bore clearance. It should be close to 0.005" or 0.12-0.13 mm for this model.
  19. Replies
    83
    Views
    6,249

    M50/52 + S50/52: Thank you all:handgestures-thumb:! The air...

    Thank you all:handgestures-thumb:!
    The air filter will be located above the left wheel. Here the most cold air under the hood and there is a free space. From it will even make a carbon tube under...
  20. Replies
    83
    Views
    6,249

    M50/52 + S50/52: In process.....

    In process..
    40853408614086040859408584085740856408554085440862
  21. Replies
    83
    Views
    6,249

    M50/52 + S50/52: More photos after the final...

    More photos after the final treatment:406194062040621406224062340624;)
  22. Replies
    83
    Views
    6,249

    M50/52 + S50/52: ..Parts are made. Next week, they will be sent to...

    ..Parts are made. Next week, they will be sent to Moscow....:music-rockout:

    40580405814058240583405844058540586
  23. Replies
    83
    Views
    6,249

    M50/52 + S50/52: Ok, guys !! The process goes !!! Here are some...

    Ok, guys !! The process goes !!! Here are some photos from our Chinese friends:
    4042940428
    :music-rockout:
  24. Replies
    83
    Views
    6,249

    M50/52 + S50/52: Items are tested in the program Solid Works Flow...

    Items are tested in the program Solid Works Flow simulation:music-rockout:.
  25. Replies
    83
    Views
    6,249

    M50/52 + S50/52: Welded Receiver I have not turned out. I decided...

    Welded Receiver I have not turned out. I decided to do a complete design of CNC machined parts. They are now made ​​in China. The overall layout and parts are as follows:
Results 1 to 25 of 39
Page 1 of 2 1 2