Close

Search:

Type: Posts; User: mj6234

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Drama drives clicks. Clicks drives ad revenue. I...

    Drama drives clicks. Clicks drives ad revenue. I think that is pretty much why this thread exists. Oh, and there is some vendor humpers pumping up their vendor of choice and the vendor haters...
  2. Replies
    4
    Views
    722

    Awesome! Thanks for the examples. That is pretty...

    Awesome! Thanks for the examples. That is pretty close to what I did.

    Another question about AFR during spool. Is there another table that controls fuel when 'lean spool' is enabled? I know that...
  3. Replies
    4
    Views
    722

    Spool Mode (Fuel) Load Breakpoints

    Has anyone rescaled the breakpoints up here? The top cell is 94 or something. For people running bigger boost, seems like not the right resolution. Especially when many of the default values have...
  4. Replies
    27
    Views
    6,713

    30mph on the big end is a ton!

    30mph on the big end is a ton!
  5. Replies
    8
    Views
    1,908

    Well issue came back. Kept getting misfire...

    Well issue came back. Kept getting misfire cylinder 6. Buddy convinced me to swap the injector with one of my old known good ones (actually one only had 2000 miles on it). I bought the Precision...
  6. Replies
    8
    Views
    1,908

    First drive on the JB4 pump flash and all still...

    First drive on the JB4 pump flash and all still seems well. I will give it a week or two and report back if things change.
  7. Replies
    8
    Views
    1,908

    Small update here. I did get my DME swapped over...

    Small update here. I did get my DME swapped over to MSD81. Drove around on stock programming for a couple days and can't recreate the issue any more. I just flashed the new DME with the latest JB4...
  8. Thread: 07 n54 misfires

    by mj6234
    Replies
    87
    Views
    23,087

    Are you still running the rebuilt injectors? I'd...

    Are you still running the rebuilt injectors? I'd just get new at this point, at least on bank 1. You can get new ones for $110/injector now. If that clears up bank 1's codes, you know what's going on.
  9. Replies
    8
    Views
    1,908

    Good feedback. I did check the ground points for...

    Good feedback. I did check the ground points for the coils. All tight and clean. I did inspect the harness as well and looked for signs of arcing, and all looked well.

    No ceramic coating on the...
  10. Replies
    8
    Views
    1,908

    I think my next step might be just to update to...

    I think my next step might be just to update to MSD81. I have had 2 MOSFETs fail (cyl 5 & 1) already and replaced them. I saw this thread and seemed like maybe it is the DME.
    ...
  11. Replies
    8
    Views
    1,908

    Odd Stumbling Issue @ 2500 RPM

    OK, need some help from the community.

    Have an issue now where intermittently I have something ranging from a minor hiccup to full on feels like a misfire and can't accelerate issue.

    I can...
  12. Replies
    25
    Views
    6,039

    http://www.bimmerboost.com/images/imported/2017/04...

    http://www.bimmerboost.com/images/imported/2017/04/4534326-1.jpg
  13. Replies
    10
    Views
    4,150

    Just to close the loop, I think I solved the...

    Just to close the loop, I think I solved the issue. Here is my post on n54tech. Disabling lean spool eliminated the behavior entirely.


    OK guys, final update. I was able to intermittently...
  14. Replies
    10
    Views
    4,150

    Pump BEF. I think that the HPFP is low due to low...

    Pump BEF. I think that the HPFP is low due to low RPM and the bank 2 trims going to 0. Tried NGK 95770 at 0.022" and stock plugs. Didn't reset adaptations after injectors, but have been running fine...
  15. Replies
    10
    Views
    4,150

    I am starting to think that the injector seal...

    I am starting to think that the injector seal could be a possible issue. Have people had problems with them failing? I found this post and seemed somewhat similar, although I don't have the idle...
  16. Replies
    10
    Views
    4,150

    I took a quick glance around to make sure all the...

    I took a quick glance around to make sure all the charge tract was still tight, and it was. My two guesses are: either the brand new cylinder 5 injector failed already (seems unlikely) or the pre-cat...
  17. Replies
    10
    Views
    4,150

    29D1 - Cyl 5 Misfire

    K, started getting this. Here is what I have done so far.

    New index 12 injectors 1500mi ago (coded as well). Car ran fine after install. until recently.
    New coils (all cylinders)
    New plugs ...
  18. Replies
    154
    Views
    56,737

    More like he slithered over to another platform...

    More like he slithered over to another platform to make grandiose promises, deliver something that sort of works, collect money, and then slither over to the next platform.
  19. Replies
    86
    Views
    20,502

    Why does it have to be car stuff? Hookers and...

    Why does it have to be car stuff? Hookers and blow?
  20. Just to follow up on this, it was the pinion...

    Just to follow up on this, it was the pinion seal. A 50mm wrench and a 62mm wrench were needed to pull the driveshaft and the pinion nut. The 50mm nut is reverse threaded but the 62mm pinion nut is...
  21. Thread: 07 n54 misfires

    by mj6234
    Replies
    87
    Views
    23,087

    Try these guys. No personal experience, but they...

    Try these guys. No personal experience, but they seem to know what they are doing.


    https://www.youtube.com/watch?v=lt5LRFQThYs
  22. Are you sure the 8psi at idle isn't absolute psi?...

    Are you sure the 8psi at idle isn't absolute psi? Meaning atmospheric pressure would be 14.7psi? 10psi at 3K would really be reading 14.3psi if this is the case?
  23. Nice. Do you have the torques at the bottom of...

    Nice. Do you have the torques at the bottom of the screenshot there?
  24. Just swapped all my injectors for index 12 and...

    Just swapped all my injectors for index 12 and did the plugs. Wow, some of them were in bad condition and leaking. Oddly cyl 5 was the best looking of all the injectors. Who knows.

    I will see what...
  25. That one looks like one of the axle hubs right?...

    That one looks like one of the axle hubs right? Mine in the driveshaft one.
Results 1 to 25 of 142
Page 1 of 6 1 2 3 4