Search:

Type: Posts; User: TurboBullett

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    93
    Views
    3,289

    Sent you a PM...

    Sent you a PM...
  2. BW is based in Germany and was a conglomerate of...

    BW is based in Germany and was a conglomerate of KKK and Switzer turbo companies.
    BorgWarner Turbo Systems
    Worldwide Headquarters GmbH
    Marnheimer Strasse 88
    67292 Kirchheimbolanden
    Germany
  3. an easy way in laymens terms to think about...

    an easy way in laymens terms to think about compressor surge is the engine is consuming more air than the compressor wheel can feed it at a certain airflow(power) and pressure ratio. some ways to...
  4. talked to one of my Borg Warner turbo...

    talked to one of my Borg Warner turbo distributors and have what may be good news and bad news...first the good, these turbos actually flow air out to the rpm lines on the compressor map obviously...
  5. Now that's very nice did not notice that I'll...

    Now that's very nice did not notice that I'll call one of my turbo suppliers and see if they can do a more suited compressor wheel in the 7670 housing! As I said previously I really like much about...
  6. If you look at the entry of the EFR you will see...

    If you look at the entry of the EFR you will see they undivide it to allow both banks to bleed off of the waste gate...at that point it's no longer a divided housing other than the a/r decrease...
  7. On the 8374 compressor map at 2.5 bar-22psi it...

    On the 8374 compressor map at 2.5 bar-22psi it will surge at less than 26lb/min or 260 HP what this means is you will get cavitation IF the turbo spools faster than the left side of the map. The...
  8. Thats alot of turbo, good to 800hp. But the surge...

    Thats alot of turbo, good to 800hp. But the surge line leaves ALOT to be desired. However I do LOVE the fact that they undivide the housing to allow wastegating of both banks. As I said I really like...
  9. I spoke to Rob at length on this subject on why...

    I spoke to Rob at length on this subject on why up to that point(prior to shivs successful attempt) no singles had been successful.
    If you understand how a turbine works it takes the exhaust energy...
  10. I posted on the other forum but would rather get...

    I posted on the other forum but would rather get into a technical discussion here... I talked w steed back in the fall on this manifold and at that point they were doing a standard twin scroll. I...
  11. Replies
    93
    Views
    3,289

    You're thinking of Anthony, and he just sold his...

    You're thinking of Anthony, and he just sold his V to a guy in Canada!
  12. Replies
    93
    Views
    3,289

    Yeah I replied that that was fine ...didn't you...

    Yeah I replied that that was fine ...didn't you get my last pm?
  13. Replies
    93
    Views
    3,289

    I don't keep cars for very long as I always need...

    I don't keep cars for very long as I always need a new one to develop parts :((
  14. Replies
    93
    Views
    3,289

    Thanks, that's my old car the AWE SilverBullet!...

    Thanks, that's my old car the AWE SilverBullet! Here's a screenshot of it in Forza2 where it's a prize car!

    15124
  15. Replies
    93
    Views
    3,289

    Yeah Silver 2000 b5 S4!

    Yeah Silver 2000 b5 S4!
  16. Replies
    93
    Views
    3,289

    Here's a pic of what I'm talking about these...

    Here's a pic of what I'm talking about these pipes press on the inlet and are sealed off with O-rings

    15091
  17. Replies
    93
    Views
    3,289

    If you send me that broken inlet pipe I can see...

    If you send me that broken inlet pipe I can see what I can come up with! I envision cutting the tube after the right angle bend to he compressor and pressing/vulcanizing in a higher flowing CNC...
  18. Replies
    1,207
    Views
    33,453

    Dzenn, what Laloosh is saying is true while it's...

    Dzenn, what Laloosh is saying is true while it's a new phenomenon in DI it's not new in forced induction, case in point back when they used to run ultra high rpm racing turbo Honda engines they would...
  19. Replies
    1,207
    Views
    33,453

    Laloosh I fully understand and get what you're...

    Laloosh I fully understand and get what you're saying... What are your thoughts on gaseous propane or natural gas in an auxiliary fuel system? It has widespread use in diesel turbo apps and both have...
  20. Replies
    209
    Views
    7,357

    Dzenno, you generally don't want to go larger ID...

    Dzenno, you generally don't want to go larger ID than the inside diameter of your throttle body, I'd say thinner wall 2.5"stainless or 2.75" thicker wall stainless or aluminum would be perfect on the...
  21. Replies
    209
    Views
    7,357

    Helix FMIC doesn't require any trimming for...

    Helix FMIC doesn't require any trimming for install!
  22. Replies
    209
    Views
    7,357

    You see had we done that it would be with an...

    You see had we done that it would be with an agenda( in the forums eyes), that's why you will never see me quote in house data and only use end user data! Because some of the "data" some vendors...
  23. Replies
    209
    Views
    7,357

    We will gladly open up helix to host for a...

    We will gladly open up helix to host for a shootout and have said so for a few years, unfortunately the only other vendor that has ever expressed interest was CP-e.(doesnt this make you wonder why no...
  24. Replies
    209
    Views
    7,357

    He DIDN'T have a Helix intercooler he had an...

    He DIDN'T have a Helix intercooler he had an intercooler fabricated that had a stepped core like the Helix.
  25. Replies
    209
    Views
    7,357

    Direct pressure drop testing is acceptable, using...

    Direct pressure drop testing is acceptable, using wgdc that can and is altered by many other factors isn't, especially when boost levels aren't even the same(why?) and in a scenario where meth is...
Results 1 to 25 of 78
Page 1 of 4 1 2 3 4