Close

Search:

Type: Posts; User: brusk

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. I'm guessing you couldn't start a new thread...

    I'm guessing you couldn't start a new thread since your new. Sent you a PM with somebody to contact for help.
  2. Replies
    67
    Views
    1,700

    That's one of the issues I've had in testing...

    That's one of the issues I've had in testing mine. I got it just for the consistency of not having to try to hold the right RPM on the launch. I found trying to set it low I could stall out if the...
  3. Replies
    67
    Views
    1,700

    I've asked this a few times but it doesn't seem...

    I've asked this a few times but it doesn't seem like too many people have used both.
  4. Replies
    117
    Views
    3,863

    Alignment should fix that. Hopefully the first...

    Alignment should fix that. Hopefully the first try. I had to go through a few alignments and just kept adding upgraded rear suspension parts each time trying to figure it out. First alignment done by...
  5. Replies
    73
    Views
    2,320

    I was hoping the internals would be compatible,...

    I was hoping the internals would be compatible, only a matter of time before we start needing replacement syncros for these trannys. The 1-2 shift was never the best to begin with. I'm going to guess...
  6. Replies
    73
    Views
    2,320

    Did I read correct that they went with carbon...

    Did I read correct that they went with carbon syncro's on the M4 tranny?
  7. I'm guessing this should be it ...

    I'm guessing this should be it

    http://www.bimmerboost.com/showthread.php?811-Reputation-system-enabled
  8. I went to the drop down for my name, general...

    I went to the drop down for my name, general settings, the on the left I chose Edit Profile and on the Bottom there was an option for Rep Power to Give.
  9. Just changed some setting to 5 on mine. Did it...

    Just changed some setting to 5 on mine. Did it give you the 5 or the standard 2?
  10. This would be nice if people started adjusting...

    This would be nice if people started adjusting this. I don't know if I've ever gotten more than a +2. Any reason why it's not automatic up to a certain point.
  11. Replies
    17
    Views
    599

    Yeah considering you can buy the Honda knock off...

    Yeah considering you can buy the Honda knock off deck guards for that price.
  12. Replies
    17
    Views
    599

    I would think an epoxy is a poor choice given its...

    I would think an epoxy is a poor choice given its reactions to certain chemicals. The Spec sheet lists several ingredients resistant level as only fair, some of these are common ingredients in...
  13. Replies
    19
    Views
    278

    Looks like MrPikolo's list is pretty good and...

    Looks like MrPikolo's list is pretty good and that link to the jack above in my opinion is a must I've got the same jack from Northern Tool with the Arcan brand on it.

    As for Brands I will say...
  14. Replies
    17
    Views
    599

    Typically you just match what is open on either...

    Typically you just match what is open on either the head or head gasket and should not have any negative affects if done correctly.
  15. Replies
    17
    Views
    599

    I've already spoken to Darton, they said they...

    I've already spoken to Darton, they said they send their BMW stuff to VAC and to contact VAC for anything questions. But that was two years ago, who knows if they've done anything since.
  16. You should probably message them back and ask for...

    You should probably message them back and ask for some more rep.
  17. Replies
    169
    Views
    5,753

    As with any confusing semi risky purchase it's...

    As with any confusing semi risky purchase it's always a good idea to email the company to get any information direct. Most don't post confusing technical data if it's not a standard practice for that...
  18. Replies
    169
    Views
    5,753

    Sorry to hear about your bad luck. I honestly...

    Sorry to hear about your bad luck. I honestly don't understand how Rob can state there's a problem with any inlet considering all of them are better than the OEM. Fitment, ALL of them fit better than...
  19. Replies
    8
    Views
    216

    Yep. I get grief from friends about it that I...

    Yep. I get grief from friends about it that I should drop in a hemi. Had one in my last truck, loved it but the heads are huge and I can pick up a 100K mile 6L for half the price of a hemi.
  20. Replies
    8
    Views
    216

    99 2WD Extended Cab 2.5 5 speed, freebie truck...

    99 2WD Extended Cab 2.5 5 speed, freebie truck basically that just needs al ot of stupid things like bushings, ball joints etc..

    Stupid spindles house the brake pads instead of a seperate...
  21. Replies
    8
    Views
    216

    I'll play it safe and go with the Ford rotors...

    I'll play it safe and go with the Ford rotors then and have them properly machined to fit the hub. I understand the out of balance part but would think that having it fit snuggly on 5 9/16" studs and...
  22. Replies
    8
    Views
    216

    Ok that's what I'm curious on, how the rotors can...

    Ok that's what I'm curious on, how the rotors can cause a vibration if they are properly centered and the hub to wheel is hubcentric.
  23. Replies
    8
    Views
    216

    Why is hubcentric rotors important?

    I'm doing a custom brake setup on my dakota due to a POS OEM design that has failed. I understand wheels needing to be hubcentric and I'm not trying to bypass that but other than proper alignment...
  24. I found the numbers that Dzenno had provided for...

    I found the numbers that Dzenno had provided for another comparison. Looks like their numbers were right on with ABR's

    http://www.bimmerboost.com/attachment.php?attachmentid=20578&d=1346765697
  25. Just curious if anybody still has Dzenno's flow...

    Just curious if anybody still has Dzenno's flow numbers to see how his local shop compared since he had one of the first setups done.

    How much do flowbench's differ? Are their built in correction...
Results 1 to 25 of 495
Page 1 of 20 1 2 3 4