Close

Search:

Type: Posts; User: Terry@BMS

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds; generated 58 minute(s) ago.

  1. Replies
    39
    Views
    2,542

    The twin disk setups are definitely hit and miss....

    The twin disk setups are definitely hit and miss. best clutch I've driven is the 335is but it's probably not going to work for much over 600whp.
  2. Replies
    39
    Views
    2,542

    Waiting for him to send me some photos so I can...

    Waiting for him to send me some photos so I can check it out for myself. No idea what could have happened. =/
  3. Replies
    39
    Views
    2,542

    Crap, Tony just told me the Spec S3+ in our white...

    Crap, Tony just told me the Spec S3+ in our white 135i looks toasted... I barely used that thing. Maybe 3x 1/2 mile events, with no hard launches. =/
  4. Replies
    7
    Views
    592

    There is no easy way to know as unlike PI we...

    There is no easy way to know as unlike PI we can't measure current cross the TBI injectors. But you could rig up a light bulb or voltmeter to the solenoid power to verify its turning on.
  5. Great idea! Sent a donation over on behalf of...

    Great idea! Sent a donation over on behalf of BMS. :)
  6. OK still confused as to what the accusation...

    OK still confused as to what the accusation against Vargas is in this thread. Can it be boiled down to say one sentence? :)
  7. OPs problem was just the voltage input stting on...

    OPs problem was just the voltage input stting on the JB4. It was set for Aquamist not BMS FSB, and is now resolved. :)

    But pumps do wear out over time so if all else fails sometimes they need to...
  8. I'm a bit confused... So the accusation is the...

    I'm a bit confused... So the accusation is the GCs (that have made 800whp) are really these same Chinese housings everyone had, but maybe ported or machined a bit?
  9. Rocking!

    Rocking!
  10. bit 4 is what has to be set to 0. If you are...

    bit 4 is what has to be set to 0. If you are unable to disable bit4 maybe interface is out of date or has some issue, feel free to email in if you need further help with it.
  11. Looks like you set the flow input for an Aquamist...

    Looks like you set the flow input for an Aquamist flow sensor, but you have an FSB sensor, right? They use different voltage ranges. So fix that under FutureUseD settings and relog.
  12. Replies
    107
    Views
    8,180

    I think AD is like a lot of shops in this...

    I think AD is like a lot of shops in this industry. Makes good stuff but prices it so low that they are unable to expand to keep up with production. I know I'm waiting to see how Donnie's 4L80E stuff...
  13. I ran a single channel bulletin board in 1990...

    I ran a single channel bulletin board in 1990 that was basically full of me and my friends arguing about front wheel drive vs. rear wheel drive... So not much has changed really. :)
  14. I don't get what all the drama is about... Chris...

    I don't get what all the drama is about... Chris Fd up a measurement and fixed it. Can't we all move on? lol
  15. Replies
    17
    Views
    1,743

    WMI flow is used to add octane and bolster fuel...

    WMI flow is used to add octane and bolster fuel pressure. If fuel trims are off adjust those in the BEF directly at the relevant load/engine speed points.
  16. Replies
    17
    Views
    1,743

    If you are relying on pump PWM to vary flow that...

    If you are relying on pump PWM to vary flow that might get tricky with two pumps. Easy enough to play with it though. If you are keeping duty below 70% FSB might be find running both of them....
  17. Replies
    17
    Views
    1,743

    Probably a good idea for twin pumps if you're...

    Probably a good idea for twin pumps if you're moving more than say 1500cc/min. But if you want to know for sure monitor line pressure.
  18. Replies
    56
    Views
    6,286

    ~170mph with ~675whp. With ~800whp prob 175mph+....

    ~170mph with ~675whp. With ~800whp prob 175mph+. The cars running 200mph are like 1200whp+ so that is never going to happen. Honestly I dislike going over 160mph in the car and find rolling races...
  19. lol not quite what I had in mind but works... I...

    lol not quite what I had in mind but works... I like to see logs of runs to quantify whether the setup is maxed out or whether it has more potential, and whether the tuning is safe or on the edge.
  20. Nice! Is there an emoticon yet for this...

    Nice!

    Is there an emoticon yet for this thread is useless without logs? :)
  21. Replies
    56
    Views
    6,286

    With the new motor shooting for around 800whp on...

    With the new motor shooting for around 800whp on a 6466. :)
  22. Can't wait to see how this setup turns out......

    Can't wait to see how this setup turns out... 700whp+ and a 4L80E should be easy 9s. :)
  23. Replies
    56
    Views
    6,286

    All is fair in love, war, and racing records. An...

    All is fair in love, war, and racing records. An E82 is only around 120# less than an E90. :)

    PS. Also have some extra weight from the roll cage.
  24. Replies
    56
    Views
    6,286

    Nice!! Can't wait to get our 135i back together...

    Nice!! Can't wait to get our 135i back together and snatch the 1/2 mile trap record back. :)
  25. Thread: PI METH

    by Terry@BMS
    Replies
    4
    Views
    1,850

    Water is probably a bad idea through PI...

    Water is probably a bad idea through PI injectors, but Steve would be the best authority for that.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4