What's on your mind?


[140]

Live Feed

mjmarovi replied to the thread BMW 335i OEM exhaust, airbox, chargpipe, intercooler, and cowl.
" BUMP! Ok guys, here's some prices for this stuff I really need to make room in the garage.

Exhaust- $100 plus shipping or local pickup

OEM Chargepipe- $40 plus shipping Has the OE diverter valves on it

OEM airbox- $40 plus shipping

OE Cowl with filter- $30 plus shipping "

Today, 08:34 PM

mjmarovi created the thread Koi Orange Plasti Dip WITH SPRAYER!.
" Alright guys,

I had the dip listed before, but now going to offer the dip and sprayer as a package deal. I'd like to sell quick so going to start off dirt cheap. Now, Koi Orange is a DYC exclusive color and normally an $11/gallon upcharge. Normally from DYC it's $282 shipped for the gallons I have which is what I paid. This is the best orange they offer and closest to the limited M3 orange BMW did on the e92.

I also bought the sprayer from DYC, and used it only for one other car which was done in a flat navy blue. You'll see a spot of orange on the sprayer, I tested out the Koi orange on a golf club to test color.

$300 shipped to lower 48 for the whole package or $280 picked up locally anywhere from Fort Myers to Tampa, FL.

"

Today, 08:30 PM

JonsC63AMG replied to the thread Article: Tune only W204 C63 AMG vs a bolt on Mustang GT 5.0 'Coyote' from a roll.
"
Quote Originally Posted by Untouchable View Post
I guess that means your c63 runs 10s. Impressive.
My friend with a cammed jeep will run you at track.
I'm simply saying that the 5.0 is in the same league as the C63. Cammed only Jeep? This is a low 11sec Jeep 440 stroker motor I ran..https://www.youtube.com/watch?featur...&v=5B-jZ6hpOIw "

Today, 08:26 PM

mjmarovi replied to the thread BMS Dual Cone Intake (white) and BMW Oil Catch Can.
" BUMP! PRICE DROP!

DCI- $90 SHIPPED

OCC- $150 SHIPPED "

Today, 08:18 PM

Sticky replied to the thread Weistec is bringing a 3.0 liter twin screw W211 E55 to Shift-Sector.
" And this looks like the motor here:

"

Today, 08:08 PM

Sticky created the thread Weistec is bringing a 3.0 liter twin screw W211 E55 to Shift-Sector.
" They just posted this. I think this is the @Weistec shop car but I'm not sure. Sounds awesome though!

<iframe src="//instagram.com/p/m8udE1o8XS/embed/" width="612" height="710" frameborder="0" scrolling="no" allowtransparency="true"></iframe> "

Today, 08:07 PM

Sticky replied to the thread Got my Blackstone oil analysis report back.....
" I love the analysis these guys do. I'll have to send mine in too. "

Today, 08:00 PM

Sticky replied to the thread Turbos are not new to Formula 1 - A look back at BMW's 1500+ horsepower M12/M13 turbo F1 motor based on the production M10 four-cylinder.
"
Quote Originally Posted by digger View Post
IMO the rods are more of a marvel than the block. there would not be many applications that involve higher compressive loads. the rods looked very beefy as in topfuel beefy
Definitely. I find the whole package impressive. "

Today, 07:57 PM

AdminTeam created the thread Xnprmy is now here!.
" Xnprmy, we appreciate you taking the time to join. "

Today, 07:44 PM

4g63man replied to the thread Eaton Supercharger Kit - E39 540i.
" Had my kit 3 months think out the box make it better and have a supercharger in that v of the m62 "

Today, 07:43 PM

Untouchable replied to the thread Article: Tune only W204 C63 AMG vs a bolt on Mustang GT 5.0 'Coyote' from a roll.
" I guess that means your c63 runs 10s. Impressive.
My friend with a cammed jeep will run you at track. "

Today, 07:41 PM

135idct replied to the thread My Top Mount Single Turbo Build 135i 6AT N54..
" any wrong with my WG connections?
should i replace the two lines to the red circle?
@Terry@BMS
@
fastgti69
Attachment 37561 "

Today, 07:31 PM

digger replied to the thread Turbos are not new to Formula 1 - A look back at BMW's 1500+ horsepower M12/M13 turbo F1 motor based on the production M10 four-cylinder.
" IMO the rods are more of a marvel than the block. there would not be many applications that involve higher compressive loads. the rods looked very beefy as in topfuel beefy "

Today, 07:12 PM

ovitrix replied to the thread Got my Blackstone oil analysis report back.....
" Looks good Steve! How many miles do you have in your car? I use the same oil like you since 50k miles. i should send a sample of my oil to blackstone to see the result. I have 120k miles. Tuned since 30k miles. "

Today, 07:06 PM

mjmarovi replied to the thread MotorTrend compares the 2014 BMW F22 M235i to the 2014 Mercedes-Benz C117 CLA45 AMG.
" IMO considering this is more of an M "package" car and not a real M car, where the MB is a real AMG car, I think the Bimmer did pretty awesome.

I'd actually like to see the CLA45 up against a 1M and then a "M2" if BMW does one. "

Today, 07:01 PM

Sticky replied to the thread Quick update - YSI at 21 psi and C16.
"
Quote Originally Posted by SpeedLimit? View Post
how long til we get some numbers?
You won't have Dynojet numbers until next month probably. "

Today, 06:56 PM

AdminTeam created the thread Let's point and laugh at ozsl500.
" ozsl500, we appreciate you taking the time to join. "

Today, 06:55 PM

digger replied to the thread Turbos are not new to Formula 1 - A look back at BMW's 1500+ horsepower M12/M13 turbo F1 motor based on the production M10 four-cylinder.
"
Quote Originally Posted by Sticky View Post
It makes the block good for F1 that it is strong right?

Yes, they raided the parts bin and found an over engineered block that made for one of the best motors in F1 history.

If you're not impressed so be it, I am.

in the modern world of F1 being strong is merely one aspect. hopefully it doesn't need to be said that it needs to be strong enough to withstand the loads it is subjected to, that is obviously a requirement. "

Today, 06:54 PM

mjmarovi replied to the thread The new sound of Formula 1....FAIL.
" I'm stopped listening once he started talking about carbon footprint "

Today, 06:53 PM

SpeedLimit? replied to the thread Quick update - YSI at 21 psi and C16.
" how long til we get some numbers? "

Today, 06:51 PM