• Renntech X5 M dyno tune and 1/4 mile results = 518 all wheel horsepower and 12.2@111.91

                    
      		   
      Published on 09-13-2011 06:10 AM
      10 Comments Comments
      Renntech seems to be spreading to all platforms and that is a good thing. Increased tuner competition should bring out the best. We received this graph showing dyno results for the Renntech S63B44 ECU tune. The car puts down an eye popping 518 to the wheels on an all wheel drive Mustang dyno along with 497 all wheel torque. There is no baseline unfortunately for which to compare the gains from. The car did run 12.7@109 stock and with the tune managed 12.2 and almost 112 miles per hour in 87 degree conditions on just 91 octane pump gas.



      This article was originally published in forum thread: Renntech X5 M dyno tune and 1/4 mile results = 518 all wheel horsepower and 12.2@111.91 started by Sticky View original post
      Comments 10 Comments
      1. Puerto Rican 335d's Avatar
        Puerto Rican 335d - 09-13-2011, 12:58 PM
        My friends from RennTech in Lakewood Florida, the owner Harmut Feyhl, Jeff and the other guys. I was the test bunny for Mini-Madness/Evo TechUSA when they did the ECU for my now sold 02 MCS. these uys rockClick here to enlarge. If you plan to use their stuff TRUST ME it works. Damn, Im going to call Or send email to Harmut about this. Good Luck Amigos!!
      1. SlicktopTTZ's Avatar
        SlicktopTTZ - 09-13-2011, 01:38 PM
        It is HARD to make that much power on an AWD Mustang Dyne! If only this drivetrain was in something lighter.....
      1. Sticky's Avatar
        Sticky - 09-13-2011, 07:32 PM
        Click here to enlarge Originally Posted by Puerto Rican 335d Click here to enlarge
        My friends from RennTech in Lakewood Florida, the owner Harmut Feyhl, Jeff and the other guys. I was the test bunny for Mini-Madness/Evo TechUSA when they did the ECU for my now sold 02 MCS. these uys rockClick here to enlarge. If you plan to use their stuff TRUST ME it works. Damn, Im going to call Or send email to Harmut about this. Good Luck Amigos!!
        You have an X5 or X6 M?
      1. Sticky's Avatar
        Sticky - 09-13-2011, 07:33 PM
        Click here to enlarge Originally Posted by SlicktopTTZ Click here to enlarge
        It is HARD to make that much power on an AWD Mustang Dyne! If only this drivetrain was in something lighter.....
        Like an M5? Click here to enlarge
      1. m54b25's Avatar
        m54b25 - 09-13-2011, 10:55 PM
        Click here to enlarge Originally Posted by Puerto Rican 335d Click here to enlarge
        My friends from RennTech in Lakewood Florida, the owner Harmut Feyhl, Jeff and the other guys. I was the test bunny for Mini-Madness/Evo TechUSA when they did the ECU for my now sold 02 MCS. these uys rockClick here to enlarge. If you plan to use their stuff TRUST ME it works. Damn, Im going to call Or send email to Harmut about this. Good Luck Amigos!!
        Yes, it seems RENNtech team have some nice decent gain on the X5 M. But, not sure if mentioned person Jeff or Evo company have much involvement on their new RENNtech X5 M inhouse calibrations Click here to enlarge.
      1. flipm3's Avatar
        flipm3 - 09-14-2011, 08:43 PM
        That kind of power on a Mustang Dyno is absolutely no easy feat. I haven't even seen a supercharged S65 hit these numbers on this type of dyno.
      1. Sticky's Avatar
        Sticky - 09-14-2011, 10:16 PM
        Click here to enlarge Originally Posted by flipm3 Click here to enlarge
        That kind of power on a Mustang Dyno is absolutely no easy feat. I haven't even seen a supercharged S65 hit these numbers on this type of dyno.
        It is a lot of power or a Mustang but a supercharged S65 with some higher boost should easily be breaking the 500's.
      1. Puerto Rican 335d's Avatar
        Puerto Rican 335d - 09-15-2011, 03:29 PM
        Jeff Katz was the programmer for my MINI, RennTech has been in business for close to 20 yrs nowClick here to enlarge
      1. Sticky's Avatar
        Sticky - 09-15-2011, 03:31 PM
        Click here to enlarge Originally Posted by Puerto Rican 335d Click here to enlarge
        Jeff Katz was the programmer for my MINI, RennTech has been in business for close to 20 yrs nowClick here to enlarge
        Yes, I think what was said though is that Jeff is no longer involved with Renntech.
      1. Puerto Rican 335d's Avatar
        Puerto Rican 335d - 09-16-2011, 02:11 PM
        Sorry misunderstood itClick here to enlarge