Close

    • E39 M5 2JZ supra turbo motor swap by E-shift Performance hits over 800 wheel horsepower on E85

      The E39 M5 here belongs to BimmerBoost member 930chas. The 2JZ-GTE supra motor was rebuilt by E-Shift Performance and has been set up for 93 octane as well as E85. The motor was recently tuned by Justin Nenni of Tuning Concepts and has put down some very impressive numbers. On 93 octane the car dyno'd 613 wheel horsepower and on E85 it put down an eye opening 848 wheel horsepower. Impressive? Yes indeed. Check out the videos and pictures below.










      Dyno 93 octane:




      Dyno E85:








      Dyno video 93 octane:


      Dyno video E85 octane:

      This article was originally published in forum thread: 2jz powered M5 dyno run started by 930chas View original post
      Comments 74 Comments
      1. Sticky's Avatar
        Sticky -
        Click here to enlarge Originally Posted by GG///M3 Click here to enlarge
        When does it make a ton of torque, and any proof?
        You can calculate the torque yourself, obviously it is making a ton. Also, the turbo was posted earlier.

        This setup is very, very strong.
      1. tjabo's Avatar
        tjabo -
        Forget building any M62s (what I was thinking of doing), this is WAAAAAAAY better! Hah hah.... SICK SICK SICK!
      1. Sticky's Avatar
        Sticky -
        Click here to enlarge Originally Posted by tjabo Click here to enlarge
        Forget building any M62s (what I was thinking of doing), this is WAAAAAAAY better! Hah hah.... SICK SICK SICK!
        It's a better option in a lot of ways. The only thing is it upsets traditionalists but then again traditionalists are sitting around figuring out how to make this kind of power or even successfully add forced induction while this is running and kicking ass.
      1. tjabo's Avatar
        tjabo -
        True true...

        I just made a complete pass through the thread here and didn't see what trans he's running. Anyone know off hand?
      1. Sticky's Avatar
        Sticky -
        Click here to enlarge Originally Posted by tjabo Click here to enlarge
        True true...

        I just made a complete pass through the thread here and didn't see what trans he's running. Anyone know off hand?
        Not sure, Tremec maybe? He is pretty good at getting back to people so I would say just wait for him to respond. Since it is a holiday replies are slow.
      1. tjabo's Avatar
        tjabo -
        Anyone seen hide or hair of the OP? I think I have a crush on this car/project... Need a fix!
      1. Sticky's Avatar
        Sticky -
        Click here to enlarge Originally Posted by tjabo Click here to enlarge
        Anyone seen hide or hair of the OP? I think I have a crush on this car/project... Need a fix!
        The OP browses frequently, just send him a PM or ask here if you have any questions.
      1. 930chas's Avatar
        930chas -
        Doohhh....sorry for the late response. I am running the factory supra v160 6 speed getrag transmission. It is badass. Shifts smoother then a stock m5 tranny and can hold 1000whp with no complaints.

        I will be updating this thread with pictures (refinished LMs look so sweeettttt) and videos in the next week or two. Just been super busy.
      1. tjabo's Avatar
        tjabo -
        What is the gearing like in that trans (i.e. freeway cruising RPMs)?
      1. Sticky's Avatar
        Sticky -
        Click here to enlarge Originally Posted by 930chas Click here to enlarge
        I will be updating this thread with pictures (refinished LMs look so sweeettttt) and videos in the next week or two. Just been super busy.
        Looking forward to it, this is one of the best E39 builds I have ever seen. The car is ridiculously awesome, and yes, again, I'm jealous. I would just like to experience it at some point.
      1. V12Godspeed's Avatar
        V12Godspeed -
        Good things take a while to come... Mad props for this awesome project. I am sure this will not dissapoint!!
      1. Jimefam's Avatar
        Jimefam -
        Click here to enlarge Originally Posted by GG///M3 Click here to enlarge
        I just looked at a dyno sheet on a car with the following specs.

        Just got off the dyno with a 7175, made 900rwhp/730rwtq at 35 psi.

        25psi, 30psi, and 35 psi all in 4th gear on a Dynojet.
        Tuned by Chris Hamilton on an AEM EMS, motor built by Joe Hussain aka "Carchitect".

        Precision billet 7175 journal bearing with a 0.96 exhaust housing
        Motor has Carillo rods, Wiseco pistons, PE bearings
        stock head with HKS 264's and PHR springs and Ti retainers, shimless buckets
        HKS 4" exhaust, 4" downpipe, on a WOTM manifold.
        ID2000cc injectors with 2 Bosch 044 pumps and teflon line setup.
        Carbonetics triple carbon clutch and TRD LSD
        Greddy 3 row intercooler and PHR breather kit
        AEM EMS with a 3.5 bar sensor, FJO wideband and NTK sensor

        Attachment 6667
        What motor is that on? I like what I see as the spool looks pretty decent. I will be running precisions Billet DBB 7685 so I'm glad to see that I should easily be able to hit my power goal with it.
      1. 930chas's Avatar
        930chas -
        This car will unfortunately be for sale. If you have any interest shoot me a PM. Nothing wrong with the car at all! Everything works and it is an absolute monster! Just times are tight in the construction industry and it doesn't look like I can afford to keep it.
      1. Sticky's Avatar
        Sticky -
        Click here to enlarge Originally Posted by 930chas Click here to enlarge
        This car will unfortunately be for sale. If you have any interest shoot me a PM. Nothing wrong with the car at all! Everything works and it is an absolute monster! Just times are tight in the construction industry and it doesn't look like I can afford to keep it.
        Oh man... noooo Click here to enlarge

        Ok, well I'd like the first crack at it. Let me know how much $.
      1. Terminator-N54's Avatar
        Terminator-N54 -
        wow that is a animal!!
      1. Sticky's Avatar
        Sticky -
        Click here to enlarge Originally Posted by Terminator-N54 Click here to enlarge
        wow that is a animal!!
        And for sale...
      1. Terminator-N54's Avatar
        Terminator-N54 -
        Pm me what he is asking.
      1. Sticky's Avatar
        Sticky -
        Click here to enlarge Originally Posted by Terminator-N54 Click here to enlarge
        Pm me what he is asking.
        Best to pm him directly.
      1. 930chas's Avatar
        930chas -
        Click here to enlarge Originally Posted by Sticky Click here to enlarge
        Best to pm him directly.
        Thanks, Sticky. Anyone that has interest shoot me a PM. We are going to start showing the car at some local meets this weekend. Should spark up a lot of interest... Not too many 900whp 2jz powered M5s out there. lol
      1. ShiftR's Avatar
        ShiftR -
        Buuurn! Basically told M engineers that they down know how to make engines.